CAW9444XQ2 Whirlpool Washer - Instructions

Super easy. Watch the video on YouTube.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Removed the attaching bolt and then removed the Upper Agitator Assembly. I removed the damaged parts and installed the Agitator Repair Kit and Re-installed the NEW Upper Agitator Assembly.

All of our wash was smelling like mildew. It was making us nauseas . After the repair everything smelled fresh and clean again. We received our parts within three days.

Thanks

snapped off the softener dispenser, pulled out the plastic seal below and could see problem. Used socket with extension to remove agitator. ran machine to verify transmission was working.
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again

take off top on middle section (pops off) pop dispenser on--done

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

I popped the cap off of the agitator. I could see the grabbers weren't grabbing the side of the agitator. I thought I could take a shot at fixing it since I was ready to give up. Happened upon this site. With the model number, I was very easily able to find the parts I needed. Ordered them up. Took one bolt out of the assembly and the whole agitator came off. I popped in the new parts as the diagram was very easy to follow, resecured the bolt, and all was good. I saved a ton of money off replacement or even calling a service tech. Your site made this very easy with the detailed diagrams. Didn't order anything I didn't need. Only cost $11 to fix it and made me feel like Mr. Fixit. I will definitely use your site as my first, best choice for any problems I have in the future.

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

took out old agitator and installed new one, machine now runs like new. couldn't be happier.

The process to replace the nylon pieces was to remove the protective cap, (which snaps in place),agitator (which is held in place with a nut) you will need a socket with an extention to reach the nut, and worn parts. replace the agitator repair kit, agitator and protective cap and your washer works as good as new. This is a very simple repair job, even a 10 yr old could do this

I took out the softner dispencer and there is a bolt under tthe the plastic cover,I removed the bolt and the whole assembly came out,then I installed the new one and reinstlled the bolt and plastic cover,and reinserted the liquid softner dispencer.All only took about fifteen min.

I simply removed the bolt from the inside of the agitator and pull the whole the straight up. It came aloose pretty easily. I took the old clothes mover off and put the new one on. On the inside of the mover the dog ears and spacer easily comes out. I removed the spacer and replaced the dogs ears. I put everything back together the way it was when I took it apart. It works as good as it did when I first got it.

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

I ordered these parts for next day delivery. The next morning they were on my door step!

I pulled off the plastic cover inside the agitator, under the softener dispenser and replaced the old "O" rign with the new one. Next I used a 3/8" socket with a 6" extension to loosen the agitator nut and removed it. The one on our machine was on rather tightly - a bit too tight in my estimation.

The upper part of the agitator lifted easily. I lifted out the cog mechanism and studied it. I took the new parts, and assembled them, using the old parts for visual reference. All of this took about ten minutes. Be sure you push firmly on the retainer until it locks in place to keep the cogs in their slots.

Next I spent about 15 minutes cleaning up the agitator just because I like to put stuff back together in 'clean condition'.

Next I replaced the thrust bearing. The instruction specified a special grease to lubricate the thrust bearing - order this when you order the parts. The original one had no grease on it and was quite worn. I used food grade vaseline. You could probably also use silicone lube on this, the part is nylon.

After I cleaned the assembly and put in the new thrust bearing, I replaced the agitator. I had slight difficulty lining up two grooves on the cog holder for the guides in the main agitator mount but got them lined up on the third try - that took less than a minute. I put the new washer on the nut, inserted the nut and tightened it down - be careful not to over tighten, just make sure it is snugged down.

Over-all this is a fairly straight-forward repair job and is not difficult - anyone who can follow easy to read instructions and run a socket wrench can do this. I would only caution to make sure the new cogs are correctly oriented in their holder. Study how the original is assembled so you can duplicate it with the new parts. Just for the record, the nut is standard right hand thread - lefty loosey, righty tighty.

I think these parts are made to fail on purpose - if the machine gets over loaded and the agitator can't work it will chew up the cogs rather than break the agitator. Good thinking on some engineer's part!

I was lucky when I found Parts Select - I'll come here for my parts from now on!

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.