WTW4850XQ1 Whirlpool Washer - Instructions

First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

Tightened up the pulley as the video showed me that might be the issue.

I do not know much about washer repair and after watching how to replace the suspension rods I decided it was not as difficult as I thought. I replaced the suspension rods and springs and that fixed the problem. The price for parts was reasonable and I received my parts in 2 days.

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.

Unplugged washer, turn off water to washer, removed water lines from washer, pull washer away from wall, removed about 5 screws from top access panel and remove, used putty knife to release clips from both sides of front control panel and lay forward, removed three screws from valve, disconnect hose from valve. Reassemble in reverse order. Not a bad idea to run a little water into bucket from both supply line to remove any foreign material that may have let lose from shut off valve before reconnecting to washer.

I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machine worked fine right after I was done.The new part was identical the the old one,and the job was a snap.

Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!

Using the parts I ordered and following the instructions provided in the video from partselect.com made the repair very easy and solved the problem

I removed the softener cup from the top of the agitator unit. The auger works separately from the bottom agitator. Remove the cap from down in the auger. There is a 7/16" bolt that holds the Auger and agitator to the center shaft. Loosen that bolt with a 7/16" socket on an extension from the ratchet wrench, and remove it from the bushing- I used a magnet. You will need to hold the agitator to loosen the bolt. Save that bolt. You will need it later. The entire agitator and auger can be lifted as a unit straight up out of the washer tub. There is a plastic bushing in the replacement kit. Slide it down over the center shaft with the small tabs up, then apply some Vaseline to the tabs as a lubricant. The new agitator can now be slipped down over the center shaft and seated on the bushing. Place the top auger onto the shaft down on to the agitator. Next, assemble the top bushing by placing the four cogs into the slots with the small pegs. The cogs must have the side with the raised area on the top of the assembly. Next push the plastic keeper down over the center of the bushing to hold the cogs in place and push it down to secure the cogs. Place this assembly into center shaft and line up the four rectangular holes in the top bushing with the four plastic prongs below. The top bushing assembly may be pushed down and secured by the four upright pegs below. If there are plastic tabs obstructing the rectangular holes in the top bushing , you can put the bolt back into the center hole and carefully tighten it down making sure the four holes align with the four pegs below. Tighten until the top bushing is securely in place. You will need to hold the lower agitator while you tighten the bolt with the socket wrench. Replace cap over the top bushing, then the softener cup into the top of the agitator assembly. The job is complete.

Hi I took off the old one and put on the new one quick and easy

Pushed the new one into place. No tools, no fuss and very little swearing involved. Clogg was caused by erroneously pouring the liquid detergent into the very handy opening reserved for fabric softener. I'd love to say my wife did that, but.... no, it was me. NOW, the real story. I ordered the part via the web at 10:00 a.m. It was delivered to me at 9:30 a.m. the next morning via Fed Ex. Wow! Great job at PartSelect.

I removed the softener cup, unscrewed the bolt and replaced the cam kit. Super easy just like everyone else said. Parts were here very quickly and at a great price!

Removed the liquid softener cartridge.
Removed the plastic seal inside the upper agitator using a pliers.
Removed the bolt holding the agitator in place using a 7/16 socket wrench with a 6 inch extension.
Lifted the agitator out.
Separated the upper and lower agitator into two pieces.
Replaced the cam assembly inside the upper agitator.
Reversed the whole process.