WTW4800XQ1 Whirlpool Washer - Instructions

Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.

I already had the old agitator out, so when I got the new one I put it in the tub. You have to spin it a little so it seats properly. I then tightened the bolt with a 7/16” socket and my wife was washing a load within 15 minutes

Followed instructions.

I went to a site that helped me diagnose the potential problems with my washer. It was the dogs that had gone bad and we're no longer gripping the upper agitator. Socket set to go in and undo the bulb the holes the upper agitator in place. You just remove the assembly that holds the dogs and I used a new washer that goes in between the upper agitator and the lower agitator. Save beaucoup bucks and it's sort of empowering for a non mechanical person. The website scared me right to you guys. And I also bought another order we can involve the upper agitator and an extra set of those dogs. Awesome company! Customer service is incredible!

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

Remove dispenser and barrier cap by hand to access cam assembly. Unbolted agitator assembly and pulled up firmly.
Able to access and replace cams. Before pulling out note how assembled and make sure to put back exactly the same. Singe person using this machine for 8 years. Poor design or quality of cams to fail so soon. Family of 5 would have been through this in a few years. For only 15 dollars definitely worthwhile repair. Parts arrived in days.

Removed the agitator and seperated the top unit notice the cam arm were worn, order the parts on line Sunday After noon and recieved the parts the next week! Great service very easy I did call customer Service checking on delivery spoke Steve who was very helpful.

snapped off the softener dispenser, pulled out the plastic seal below and could see problem. Used socket with extension to remove agitator. ran machine to verify transmission was working.
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again

take off top on middle section (pops off) pop dispenser on--done

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

The info. was really helpful

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

I unscrewed the agitator and pulled it out. Then took out the old agitator cam kit and put in the new one.

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.