WTW5200VQ2 Whirlpool Washer - Instructions

Removed the softner dispenser and lifted up the plastic piece under that. Used a 9/16th socket with a long extension and unscrewed the center bolt.
Lifted the entire agitator parts off and out.
Next had to get husband to separate the top from the bottom, it was really hard for me. I am a woman but not weak!!
Replace the washer and the other 2 parts, and put it back together and it all took about 15 to 20 minutes.

Easy repair, even for a woman!!!

I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and did that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.

While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.

Basic replacement so easy my nine yr old daughter did the needed repair we watched the video on your web site Way to go Alexis . Ten minutes later all done ! Probably saved a few hundred dollars or more, no service calls or no need to replaced our beloved washer (Cira 1994) they really don't make them like this anymore, will use your company again if needed Thanks !!!

Took the cup for the clothes softner out, just pulls out, took plastic seal out, just pulls out, took the socket set,with an exstention, unscrewed the bolt & pulled out the agitator. easy. Reverse the process in putting the agitator back. P.S. Right hand thread.




.

Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.

Unplugged the washer from the power. Turned off the hot and cold water. Took two screws off the back and raised up the upper cover. Took the power cables and water tube loose from the water level switch. Removed the switch. Put the new switch in. Removed two metal clips at the top of the washer and leaned the washer body forward. Replaced the tube with a new one. Put the washer body back in place and put the clips back in. Attached the tube to the new switch along with the power cables. Let the top cover back down and put in the two screws. Slid the new knob in place. Plugged up the washer to the power. Turned the hot and cold water back on. And commenced washing laundry.

Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

placed washer on side and installed new pads
and returned washer upright

I thought that the lid switch was the problem why the washer would not perform the drain or spin cycle. I broke the lid switch by moving the wires around. I rigged it so my daughter could use it by screwing a screw in the switch til the new one came in. After a few days, the machine stopped working again as stated above with the motor. I purchased a new Whir-pool washer for her and later found a white wire that connects to the electric motor was burnt around the connector in that only one tiny wire was still attached. I reconnected the wire in the connector and the washer started working again.

First I removed the plastic panels on each side the control panel. Each side was secured by a phillips screw. Once the screws were removed the side panels were easily removed. I tilted the panel back to the rear of the washing machine to expose the lid switch. I first took a picture with my camera phone to ensure installing the switch correctly. I removed a small screw that secured a green ground wire. The lid switch was removed by lifting the plastic catch with a flathead (or slot) screwdriver and uplugging the switch. Reverse the steps and install the new switch. Secure and tighten the green ground wire. The lid must be lifted to properly seat the lid's guide arm into the lid switch. Replace the side panels and tighten the phillip screws. Test the wash cycle using a low water level. It took me 5 minutes to install this part. I am a attorney not a mechanic.

Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

Took an educated guess it was the lid switch and after playing with the switch got it to work. Ordered new switch. The hard part was to find the model number and thanks to customer service sticking with we. we found the info and was able to come up with a part number. Re placing the switch is very easy but I had to remove the cast after trying to open the machine the wrong way. So a little body work. I also found the frame was cracked and with a fender washer on the other side of the front feet was able to fix that. Washer run great a lot is a lot quieter.THANKS!!

First unplug the washing machine.
Then used a putty knife pushed under the endcap area to release the clips holding the top console down, then lifted the front of the console and tipped it back. Held it in that position with a short piece of wood.

The lid switch was visible right there on the left. Then unplugged the switch, removed the metal screw holding the ground wire, pressed the locking tab on the switch, lifted the washer lid about 3 or 4 inches, and removed the switch. Installation was the reverse procedure. Total time about 10 to 15 minutes.