WTW7600XW2 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NEWPORT BEACH, CA
- Parts Used:
- W10247710
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Changed out suspension springs
Follow step by step YouTube channel for this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor m from campo, CA
- Parts Used:
- WPW10178988
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
mins after start it stopped and got code f51. then put it manual spin and got UL code
followed repair manual for code f51.ordered/replaced Rotor Position Sensor {RPS} disconnected and reconnected wiring harness at computer module and then put everything back together and that took care of the problem, It;s been working good since. that sensor was delivered the very next day. that was great. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORWOOD, NY
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Very noisy, compared to the original drain pump.
1st watch a video on replacement of this pump.
My main issue was the guard I had to install and the correct way to
put it in. I know I got it right.
The pump is very noisy, loud!
It pumps out just fine.
Want to know if this is normal, Loud pump.
Let me know.
Thanks, Dave
My main issue was the guard I had to install and the correct way to
put it in. I know I got it right.
The pump is very noisy, loud!
It pumps out just fine.
Want to know if this is normal, Loud pump.
Let me know.
Thanks, Dave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corey from RUSSELLVILLE, AR
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water would not drain.
Follow the video instructions.
No brainer..
No brainer..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from BEND, OR
- Parts Used:
- W10820039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Loud banging during wash cycle
This is an easy one. Snap off the agitator cap with a screwdriver.
Remove the single but and agitator.
Remove 6 phillips head screws.
Lubricate the bearing and coax it off the spindle.
Remove the single but and agitator.
Remove 6 phillips head screws.
Lubricate the bearing and coax it off the spindle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from LAKE ODESSA, MI
- Parts Used:
- WPW10309358, WPW10309357, WP8563964
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The lid on our washer would not close fully or stay up when opened.
I removed the two hinges in the lid by unscrewing them from the lid and sliding them out from the underside of the lid. I also needed to replace the hinge assembly in the washer body on the left side. I unscrewed the three screws in the back of the controls module and lifted the cover off. I unscrewed the furthest forward and left screw that went down to the hinge assembly. I then removed the trim ring around the bleach pour spout and unclipped the bleach hopper from the lid. Next I unlatched the lid assembly with a metal putty knife. Once inside I moved the bleach hopper out of the way and gained access to the left side hinge assembly. I removed the other screw holding the hinge in place and changed out the hinge assembly. I then worked backwards putting screws and pieces back in place. Finally, I installed new door hinge pins in the left and right sides to reattach the lid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PUYALLUP, WA
- Parts Used:
- WPW10619844
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid lock lite would not activate.
The most difficult was to lift the top up. Releasing the clips was tough to push in and it broke some porcelain. The 3 screws on the plastic instrument cover was all that was required. Track the wires and remove the plug in and pull the wires through the access hole and misc clips, a Phillips screw driver removes the plastic switch .Simply place the new switch under the lid and the worst is done. Once the lid was up, 10 minutes and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from DUBOIS, WY
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water would not drain from tub.
Used shop vac to remove as much water as possible. Turned washing machine on side to access pump. Removed old pump. Installed new pump. Used nutdriver to attach three fasteners and pliers to attach clamps to hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from WOODSTOCK, CT
- Parts Used:
- WPW10619844
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
"dL" error code on display. Lid lock mechanism not working.
This was the second time I did this repair, so it looks like this mechanism lasts about 3 years. I found the video instructions on your website very helpful, with one major exception. On my Maytag Bravos XL machine, there are no clips on the front of the top plate to release by pushing in a putty knife. Rather, there are two vertical brackets on the back of the top plate that are loosened or removed, and then the top can be slid forward about an inch and lifted up.
Also, the tiny electrical connection plugs are secured by plastic clips on the sides of the receptacles. Those clips just need to be spread apart a little in order to unplug the connectors; i.e., don't pull too hard on those plugs, or look for a release lever on the plugs themselves.
Repair is straight-forward. Thanks!
Also, the tiny electrical connection plugs are secured by plastic clips on the sides of the receptacles. Those clips just need to be spread apart a little in order to unplug the connectors; i.e., don't pull too hard on those plugs, or look for a release lever on the plugs themselves.
Repair is straight-forward. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George E from OCALA, FL
- Parts Used:
- 3184020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
the fastener became loose and dropped into the stove
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
George Clark
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ace from VENICE, FL
- Parts Used:
- W10205824
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The spin cycle was very noisy & shook the whole machine.
The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.
By the way, it didn’t solve the problem.
Paul
By the way, it didn’t solve the problem.
Paul
Was this instruction helpful to you?
Thank you for voting!
A rat ate holes in several rubber elbows in our washer
I got the three rubber elbows to quickly (at an additional price). They were the correct part and fit exactly. I replaced the aggravating spring clamps with new radiator-type screw clamps which made the job easier and in my opinion better. Then I devised a little hardware cloth "fence" around the bottom to the washer to keep the rat out. The job is tough enough in that you must tip the washer forward to get at the lower elbows. Also probably a good idea to adjust the feet "in" as far as possible to minimize rodent access from the bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hollis from Mountlake Terrace, WA
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
leaking
old pump had plasitc fatigue allowing water to leak from drain pump. Noticed new oem pump was reinforced in that spot, so must be common problem. new pump came with heat shield that old pump did not have, not a problem though. Placed washer on front side down on floor. removed old pump, installed new pump
Was this instruction helpful to you?
Thank you for voting!