WFW9300VU02 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Tonawanda, NY
- Parts Used:
- WP8183270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not lock
Did the repair just like the video on your website. Was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Lake Stevens, WA
- Parts Used:
- WP8183202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Couldn't be any easier!
I am a 63 yr old woman. I was able to remove the washer door, take off the broken hinge, install the new hinge, and place it back on the front of the washer in less than 15 minutes! It is a front load washer and designed for one person to do this. I YouTubed a less that 2-minute video first. The hinge fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from TULSA, OK
- Parts Used:
- WPW10352973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not fill
replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from NEWBERG, OR
- Parts Used:
- WP8182119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The video supplied by you was great and it worked very well.
It was fast and pretty easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from PLYMOUTH, IN
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
WASHER WOULDNT DRAIN F21
REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billie from Dixie, WV
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Wasn't draining
Washed three loads and it was ok but then it stopped draining again. I don't know what to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracey from Salem, OR
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Drain pump wasnt working
Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Houston, PA
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer fails to drain water
First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.
Was this instruction helpful to you?
Thank you for voting!
Bellows stained
I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Chino HIlls, CA
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Bellow torn at bottom - significant water leak
Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lon from Cadet, MO
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Water was running into machine when it was off!!!
Of course the machine was not plugged in & water valves where off. I took water hoses off. Then i took 3 screws off the back of lid & slid lid back & lifted it off. I then unplugged two wires going to valve. I then took water hose going to valve off. Last there is one bolt holding valve to machine & in the mechanic industry we call this bolt a star head, so it was a good thing I had this tool. So if you do this repair you will have to get this tool. This job is easy to do & Part Select was 100% on my order & shipping! I will order again when something brakes again !!! Thank's
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Sharon, MA
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Tub fills with water between washings
Disconnect the hot and cold water supply hoses from the rear of the machine. Remove 3 screws in the rear that fasten the top cover. Slide the cover rearward and remove it. Disconnect the black outlet hose and unsnap the two electrical connectors from the water valve. Remove one screw that fastens the water valve to the rear panel. Slide the water valve away from the screw and remove it. Reverse this procedure to install the new valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Prattville, AL
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front loading washer would collect water in the tub after use.
Disconnected the water supply lines. Removed four screws holding the top to back frame. Removed the top. Disconnected the electrical valve connections. Removed the valve set mounting screw. Removed the valve set and replaced. Reversed the steps above for installation.
Was this instruction helpful to you?
Thank you for voting!