MTW5920TW0 Whirlpool Washer - Instructions

Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.

The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.

I watched the videoand just followed your lead. It really was easy. The only thing I didn't have was the agitator grease or lube.

removed old hose clamps and hose using pliers. Installed new hose which had all new clamps preinstalled on new hose.

Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.

Pulled up on fabric softener dispenser and removed it. Had to use pliers to remove cap and seal to get access to the bolt holding the agitator in.

Realized my socket extension wasn’t long enough so went to Lowe’s and bought another.

Was unable to hold the bottom of the agitator to keep it still and get enough leverage to remove the bolt. I poured hot water over it and then climbed into the washer and used my foot to hold the vanes still while I removed the bolt. Once I got the agitator out, the rest was a breeze. Separated the top of the agitator from the bottom by placing it on the floor, using my feet to hold it down and pulling up to remove the top part of the agitator.
Turned the top of the agitator upside down and removed the cam and feed dogs. Assembled the new one and held the agitator top horizontally while placing the new part back in.
Reassembled the top and bottom of the agitator and put it back into the washer. Tightened the bolt, replaced the cap with its seal and pressed the fabric softener dispenser back into place.

Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished

I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

with pliers removed remaining broken part on selector switch
attached new knob sliding fool proof groves on innerside now we are back in business, myself and family thank you for the support

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the clamp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.

After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.