GHW9300PW4 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Darrell from Lady Lake, FL
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pump not working
Replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Harrington Park, NJ
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door handle broke off
My 12 year old son did it in about 3 minutes. I wish I had oredered more because it is sure to break again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Los Angeles, CA
- Parts Used:
- WP8181887
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser Drawer Handle keeps coming off.
Just popped new one in in less than 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francisco from DELTONA, FL
- Parts Used:
- WP8182862
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Tub filling when power was off due to inlet valve leak.
Followed instructions as shown on repair video at site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUSTIN, TX
- Parts Used:
- WP8182862
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disconnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- claude van from big sandy, TN
- Parts Used:
- WPW10388414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
tub would not turn
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from OMAHA, NE
- Parts Used:
- WPW10467168, 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
PUMP HOUSING LEAKS
REMOVE AND REPLACE. FLEXIBLE RUBBER CONNECTOR WAS NOT A EXACT REPLACEMENT, THE ORIGANIL HAD A BACK STOP VALVE, NOT SURE OF THE EFFICATE ON MACHINE.
Was this instruction helpful to you?
Thank you for voting!
Torn bellow lip
Replace bellow with help from Youtube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from TARPON SPGS, FL
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Spring balanced tub violent shake on spin
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evette from Mayfield, NY
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the pump wasnt puping out the water
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Chicago, IL
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door handle
First I removed the two screws that hold the door handle in place. I then pulled the door handle off and replaced it with the new one. As long as partselect.com is around I'll be able to keep my appliances longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Mosinee, WI
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Super easy replacement. 2 Screws and a regular screwdriver or a #20 torx will work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Amherst, OH
- Parts Used:
- WP8182634
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
Was this instruction helpful to you?
Thank you for voting!
I had a leaking around the door.
I took off the front lower panel and the top panel. I also removed the door. I used the screwdriver to remove the first spring and then loosed the screw on the second ring that holds the bellow in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Gary, TX
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The washing machine was not draining. It was showing a code on the washer of 02.
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Was this instruction helpful to you?
Thank you for voting!