GHW9300PW4 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from PALM BCH GDNS, FL
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water leaking into drum when machine shut off
Shut off water. Unplug electric. Remove top panel. Unhook hoses. Unhook tubing unplug solenoid. Use torx to remove part. Reverse steps to install new part. Replace top panel. Hook up water & electric.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Sharon, MA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door handle broke
It took more time to find the right screwdriver bit than to do the replacement. Removed the 2 screws holding the handle. Put new handle in place. Put the 2 screws back in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from arvada, CO
- Parts Used:
- WP8182634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Following The Instructions Of The Repair Manuel,
First I removed the retainer ring and then pulled back enough of the boot to get the door switch out and plugged in the new switch put the retainer ring back on and it was finished. With out the repair book I would have been lost on how to do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAURA from SPARTA, KY
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
washer not drain or spin
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Day from Basking Ridge, NJ
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle was worn out/broken
No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from chetek, WI
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
baffle connectors worn off
Placed baffle inside of washer and pulled to lock into place. EASY!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from PALESTINE, IL
- Parts Used:
- WP8182862
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Whirlpool front load washer drum filling with water after use.
Followed the installation video instructions. Removed the washer top with a 1/4” nut driver torx bit. Shut off and unhooked the water lines to the washer. Took one screw off of the solenoid valve on the washer back. Removed the water line on the solenoid on the inside with a pair of pliers. Installed the new solenoid in reverse order. It took maybe 10 minutes to take off and replace. Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEWBERG, OR
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Torn bellows was leaking and eating clothes
Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
Would not pump water out at end of cycle.
First you need to remove the water from the machine, a shop vac hooked to the drain line works very well. Next remove the lower front panel ( two screws at bottom corners) and unplug pump. Remove the hose clamps and remove the hoses. Remove the screw at the front of the pump assembly and pull toward you and lift up. Instal new pump in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Victorville, CA
- Parts Used:
- WP8182634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door latch would not lock
Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gopaul from Queens, NY
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Bellow was damaged,water leakage.
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from REPUBLIC, MO
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ripped bellowspul
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from TARPON SPGS, FL
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Spring balanced tub violent shake on spin
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from MORGANTOWN, PA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door bellows had a cut in it
I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.
Was this instruction helpful to you?
Thank you for voting!