WTW6200SW3 Whirlpool Washer - Instructions

put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks

Replaced rods with new set of 4

we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved

Well i watched a video on youtube that demonstrated the repair, and it seemed easy enough, so i ordered the parts which arrived quickly enough that we avoided a trip to the laundry mat, very cool! So i did just what they said to do, unplug machine, tape down the lid, use a putty knife to pop the retaining springs in front. I used a long screwdriver to hold up rod on top and then rotate the ball around and let the rod fall through, them i used a yard stick to pop out cup on bottom. I did have assistance holding the drum back so i could see, Then i reversed the process with a new rod. The only reason it took 30 min was i did not put the cups under the balls on top, because it didnt have them in the first place, i decided to put them in after then reading the instructions. The machine runs like new, and my wife is very happy!!

Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!

Thanks guys.

At the time that I received the order part, Me and my Wife and 15 years old Douther got on it. We removed the very top of the counter and replaced once at the time every supension rod cleaned nice and neat. then we put the top on it's place conected the water hoses pluged it in and it was ready to roll.

First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.

Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.

It was not easy but I dit my sell

Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.

Disconnect power and water. Remove the back panel of the washer. The drain pump is on the lower left corner (looking at the washer from the back). Access the electrical connection to the pump motor by lifting the lid where the wire enters the motor. You should be able to do this with your fingers and moderate pressure. Disconnect the electrical plug from the pump motor. Use pliers to remove the two hose clamps, one on the inlet and one on the outlet. Water may leak at this point so have some towels ready. Using a 5/16 wrench/nut driver, remove three hex head self threading bolds that connect the pump and motor to the underside of the tub. The replacement pump and motor go in in reverse order. Note that the replacement pump comes with a moisture shield. The shield installs on top of the new pump between the tub and the pump. It is difficult to see how the shield fits in place when fitting it to the replacement pump. The best way to see how the shield fits in place is to align it on the tub where the defective part was removed. Before testing the repaired washer, consider removing the inner tub and drain compartment cover (located at the bottom back of the inside of the washer). This takes some effort; however, it will save you from repeating this repair. Look for coins or other debris under the inner tub. For instructions on removing the inner tub and drain cover, go to youtube to watch or search for the model number and tub removal on your favorite search engine or youtube. Finally, use the spin and rinse cycle to test the repair. Look to see the pump drains the washer and ensure there are no leaks around any of the hose clamps. Good luck with your do it yourself home repair.

Removed cover and removed rods,replacing them one at a time.

need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.

Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.

All went good until installing the rollers. I put a rubber ban around them to hold them in place so I could put the upper and the lower parts together. I had a string tied to the rubber ban so all I had to do is pull the rubber ban out and the rollers stayed in place.