Models
>
WTW6200SW3
WTW6200SW3 Whirlpool Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WTW6200SW3
Viewing 4 of 4Manuals & Guides for WTW6200SW3
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
Order within the next 9 hrs and your part ships today!
$136.02
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
In Stock
Order within the next 9 hrs and your part ships today!
The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.
In Stock
Order within the next 9 hrs and your part ships today!
$37.73
The purpose of this part is to help drive the outer spin basket in your washer during the spin cycle. If your washer is not spinning or agitating, you may need to replace the drive hubs. This genuine ...
In Stock
Order within the next 9 hrs and your part ships today!
$11.80
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
Order within the next 9 hrs and your part ships today!
$94.96
This part makes sure that the lid is shut before allowing the machine to start or agitate.
NOTE: This is a manufacturer substitution. Part may differ in appearance but is a functional equivalent to prior parts including
In Stock
Order within the next 9 hrs and your part ships today!
$8.00
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
In Stock
Order within the next 9 hrs and your part ships today!
The suspension rod kit supports the wash drum and keeps it stable during unbalanced loads. If your washer is making a loud banging sound during the washing cycle, check to ensure the suspension rods a...
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
$11.80
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
$43.95
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To c...
In Stock
Order within the next 9 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WTW6200SW3
Viewing 11 of 11Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Locking Issues
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from BARRINGTON, IL
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Loose change entered drain pump, cracked housing leaked all water out
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.
Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover ... Read more over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.
At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).
Re-assemble using new pump.
Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover ... Read more over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.
At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).
Re-assemble using new pump.
Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Turnersville, NJ
- Parts Used:
- WPW10189966
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer always stopped at the 47th and 24th minute of each load and display F1 error code. I would have to press "cancel" and then "start" a few times for it to continue.
Removed the dial control top covering by unscrewing the 3 screws in the back of the cover. Once the cover was off, the control module was exposed and all I had to do was:
1. Disconnect the wires that were plugged into the control module
2. Remove the old module. There was 1 screw holding it in place.
3. ... Read more Replace with the new module. Put back the screw back.
4. Reconnect the wires. There was about a 8 different plugs that needed to reconnected. So I took a few pictures of how the wires were connected/plugged in, with my compact camera (just in case I forgot where each went). I didn't need to use the pictures, but it was just a safety net in case I forgot where each went.
1. Disconnect the wires that were plugged into the control module
2. Remove the old module. There was 1 screw holding it in place.
3. ... Read more Replace with the new module. Put back the screw back.
4. Reconnect the wires. There was about a 8 different plugs that needed to reconnected. So I took a few pictures of how the wires were connected/plugged in, with my compact camera (just in case I forgot where each went). I didn't need to use the pictures, but it was just a safety net in case I forgot where each went.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Alleyton, tX, TX
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Water pump for draining
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring cla
... Read more
mps, unhooked the wiring( its a single plug in) and reverse the procedure for installing.
I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.
I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.
I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
Read less
Was this instruction helpful to you?
Thank you for voting!