2DWTW4845EW3 Whirlpool Washer - Instructions

I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

Removed top agitator bolt lifted agitator out and replaced ring and geared dogs. replaced Agitator top swirl vanes. It would have been nice if the kit included agitator grease and a new bolt and washer.

I ordered a whole agitator repair kit. Had a few problems getting everything to line up right.Finally figured out what I needed to do and everything worked like it should.

I removed the agitator top cap first. I reached inside and removed plastic cap. I then removed the 7/16 bolt inside the agitator and lifted it out of the machine. I put my foot on the bottom part of the agitator and pulled the top part off. I removed the plastic bushing in the bottom part and then removed the plastic bushing with the dog ears and the bolt. I used some appliance grease on the bushing on the bottom part and slid the top part of the agitator back in place and replaced the 7/16 bolt. It worked like a charm. My wife says I'm her hero. Thanks for making it so easy.

Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting noise. Reassemble. The drawing on this site is helpful.

I ordered the part and watched the installation video. It would have helped if I had watched the video all the way through at least once. Instead I paused and restarted it as I did the repair. As a result I had a hard time putting the agitator back together. Otherwise it was a fairly easy repair and my 20-year-old washer works great again!

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.

I removed the fabric softener dispenser atop the agitator. I twisted and pulled out the plug inside the agitator. Using a socket on an extended wrench, I removed the single nut inside the agitator (keep the agitator from turning with a large screwdriver, etc. and turn the nut counter-clockwise to remove). The agitator came out, and I removed all of the cam parts. I cleaned all of the old parts with bleach and water. Reinstalling the new parts was simple and straightforward as indicated in the illustrated instructions. Now it works great!

I popped the cap off the agitator removed a bolt. Removed the damaged parts. And replaced them with the new ones it was easy.

1. Unplugged the electrical cord
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar

Popped of lid on agitator and stuck the dispenser in. Fit perfect, works like it should. Thank you for getting me the right size part!

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.