3RLSQ8033RW2 Whirlpool Washer - Instructions

removed top controls panel (not obvious),then released old switch by rotating 90 degrees (after disconnecting wires and pressure sensor tubing), then reinstalled new switch (new switch has only 3 positions, not 5 as old switch had) and reinstalled everything else.

A 'gotcha' is the plastic 'strap' on the back that anchors switch compartment to the back steel sheet. It is EASY to dislodge that plastic strap from the bakc panel and it drops down inside the panel--maybe to the floor, maybe not--requiring difficult retrieval. Suggest TAPING the plastic strap in place on the back steel sheet so it will not fall out.

Removed the softner dispenser and lifted up the plastic piece under that. Used a 9/16th socket with a long extension and unscrewed the center bolt.
Lifted the entire agitator parts off and out.
Next had to get husband to separate the top from the bottom, it was really hard for me. I am a woman but not weak!!
Replace the washer and the other 2 parts, and put it back together and it all took about 15 to 20 minutes.

Easy repair, even for a woman!!!

Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the long shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.

Just bought my washer and dryer from Home Depot, but bought an Admiral model that didn't come with a fabric softener dispenser. Ordered the part from PartSelect and after rocket fast shipping installed it in seconds. The installation required no tools as the dispenser just snapped right in. My clothes are now soft and free of static cling. Thank you PartSelect!!

Took the cup for the clothes softner out, just pulls out, took plastic seal out, just pulls out, took the socket set,with an exstention, unscrewed the bolt & pulled out the agitator. easy. Reverse the process in putting the agitator back. P.S. Right hand thread.




.

While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.

I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and did that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.

Basic replacement so easy my nine yr old daughter did the needed repair we watched the video on your web site Way to go Alexis . Ten minutes later all done ! Probably saved a few hundred dollars or more, no service calls or no need to replaced our beloved washer (Cira 1994) they really don't make them like this anymore, will use your company again if needed Thanks !!!

placed washer on side and installed new pads
and returned washer upright

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.

First I removed the plastic panels on each side the control panel. Each side was secured by a phillips screw. Once the screws were removed the side panels were easily removed. I tilted the panel back to the rear of the washing machine to expose the lid switch. I first took a picture with my camera phone to ensure installing the switch correctly. I removed a small screw that secured a green ground wire. The lid switch was removed by lifting the plastic catch with a flathead (or slot) screwdriver and uplugging the switch. Reverse the steps and install the new switch. Secure and tighten the green ground wire. The lid must be lifted to properly seat the lid's guide arm into the lid switch. Replace the side panels and tighten the phillip screws. Test the wash cycle using a low water level. It took me 5 minutes to install this part. I am a attorney not a mechanic.

I thought that the lid switch was the problem why the washer would not perform the drain or spin cycle. I broke the lid switch by moving the wires around. I rigged it so my daughter could use it by screwing a screw in the switch til the new one came in. After a few days, the machine stopped working again as stated above with the motor. I purchased a new Whir-pool washer for her and later found a white wire that connects to the electric motor was burnt around the connector in that only one tiny wire was still attached. I reconnected the wire in the connector and the washer started working again.

Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

Unplugged the main power. Removed the 2 screws in the back and top of the control panel. Pulled control panel forward and tipped towards me to remove from top of washer. Removed the ground wire screw with a socket/ratchet. Removed the switch by pressing the tap inwards. The tab was brittle and broke. Replaced the switch, ground wire with screw and the control panel. I notice that the 2 screws which secure the switch lever/hinge to the lid were loose. These 2 loose screws were actually the problem in the first place. The loose lever was not making good contact with the switch. I think the switch was actually fine but since I broke the tab on the switch I needed to replace it anyhow. Plugged in power cord and washed a load.