1CWTW4845EW3 Whirlpool Washer - Instructions

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

Repair was extremely simple by using the video provided online. Works perfectly! Thanks so much.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

The repair was exactly like the instruction vidio

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.

7/16 socket removed nut and very easy to take apart replaced agitator. Spring knob just pop in. Awesome doing it myself and not having to spend over a hundred dollars to get a $20 job done!

Replaced agitator sprage kit. Simple instructions simple repair

Inserted a straight slot screwdriver into the small opening between the Fabric Softener Dispenser and the Agitator Assembly. Twisting the screwdriver slightly, causes the dispenser to separate from the agitator exposing a 7/8" bolt. Using the proper socket, removing the bolt allows for the removal of the complete agitator assembly. Reverse this process to install the new complete agitator assembly.

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

I removed the softener cup from the top of the agitator unit. The auger works separately from the bottom agitator. Remove the cap from down in the auger. There is a 7/16" bolt that holds the Auger and agitator to the center shaft. Loosen that bolt with a 7/16" socket on an extension from the ratchet wrench, and remove it from the bushing- I used a magnet. You will need to hold the agitator to loosen the bolt. Save that bolt. You will need it later. The entire agitator and auger can be lifted as a unit straight up out of the washer tub. There is a plastic bushing in the replacement kit. Slide it down over the center shaft with the small tabs up, then apply some Vaseline to the tabs as a lubricant. The new agitator can now be slipped down over the center shaft and seated on the bushing. Place the top auger onto the shaft down on to the agitator. Next, assemble the top bushing by placing the four cogs into the slots with the small pegs. The cogs must have the side with the raised area on the top of the assembly. Next push the plastic keeper down over the center of the bushing to hold the cogs in place and push it down to secure the cogs. Place this assembly into center shaft and line up the four rectangular holes in the top bushing with the four plastic prongs below. The top bushing assembly may be pushed down and secured by the four upright pegs below. If there are plastic tabs obstructing the rectangular holes in the top bushing , you can put the bolt back into the center hole and carefully tighten it down making sure the four holes align with the four pegs below. Tighten until the top bushing is securely in place. You will need to hold the lower agitator while you tighten the bolt with the socket wrench. Replace cap over the top bushing, then the softener cup into the top of the agitator assembly. The job is complete.

I simply watched the brief video supplied on both the page as well as my emailed receipt and performed the steps as directed. There were no deviations required... it was exactly how the video described it. Honestly, I expected a more lengthy and complicated repair!

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.