SWS833HS0 Westinghouse Washer - Instructions

Really liked how easy it was to identify the part on your website, thank you.
Opened the package, pushed on the knob. FIXED! YEA, no more pliers!

Just put the the new one on. Parts select was easy to order and fast delivery thanks again.If I ever need a part i will be sure to come back to your site. Thanks so much... Mike Brooks

After receiving the part, I easily replaced it. I didn't need any tools and it took less than 2 minutes to fix. Also, the dryer seems to be working better altogether. Basically, I just inserted the knob where it was before.

I received the Dryer knob in the mail the next day. All I had to do was slip it on. Very easy installation.

No tools was required. Last month the knob broke on my washer. I done a Google search and parts select came up. I felt comfortable ordering online from them because of their reputation. I got the part faster than I expected....my wife was happy too!

Just push the new knobs on slot. Very simple process. The best part is that it was relatively cheap and the shippping to my home was fast. Thanks.

Took it out of package..pushed it on.

my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!

Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.

First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come off so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!

Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reverse of removal.

Removed screws at back securing top panel (4).

Removed screws holding water inlet valve to back of machine (2)

Removed water hoses to bucket

Removed squeeze clamp securing water distribution hose from inlet valve

Reversed method with new valve.

Very fast...~25 min
Works fine so far!

Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the control panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!

The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.

It is so great to be able to turn my dryer on now without using my bare hand to turn the shaft that the knob was to go on. Nothing needed other than pushing knob in place. I so wish I had thought of looking online for a replacement part 4 years ago. Thanks!