SWS1339CC2 Westinghouse Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Port Monmouth, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt stretched out
lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Oquossoc, ME
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
A Leak In The Water Inlet Valve
It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from fostoria, OH
- Parts Used:
- 137221600
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't drain completely and wouldn't final spin
before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Humberto Aarón from Castroville, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
The washer hose assembly had mutiple tears in the bellow section of the hose, towards the outlet net the spout.
Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Smithfield, PA
- Parts Used:
- 131605901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Clothing/Sheets/Towels snagging in washer
The repair was very simple. Just remove the fabric softener container at the top of the agitator and there was a cover with a little plastic "hook" on the top. Just take a pair of pliers and pull on the hook pretty hard and it pops off. Then using a 1/2" socket, loosen and remove the bolt and pull off the old agitator. Slide the new agitator over the "drive shaft" where the old one was, tighten the nut, put the cap back on, place the fabric softener tray back on, and I was back in business. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Trinidad, CO
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burning smell from wash, needed new drive V belt
watched the video on website, printed instructions for feedback.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Clatskanie, OR
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad belt
did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from Buyck, MN
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Cold water would not shut off on washer
Quick google search brought me to this site, part was very easy to locate and purchase. The part was delivered within 5 days and 2 screws, 2 wires, 2 hoses, and 15 minutes later it was a done deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherry from ellenburg depot, NY
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water would not drain or spin out all the way
Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sammy from Notasulga, AL
- Parts Used:
- 137221600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not Draing Water
Good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Dania Beach, FL
- Parts Used:
- 131605901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench set
When the washer was filling up with water it would not stop and overflowed. This only happened once.l I called Frigidaire & was told I needed a new agitator & could replace it myself.
My Son replaced Dual Action Agitator & said it was easy. He did it in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William J from Prattville, AL
- Parts Used:
- 131901400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
water leaking when washing machine went to spin
removed two screw at the bottom of front panel and pulled down on panel to remove, determined water coming out splash seal, splash cover held on with plastic clips around cover. Removed two screws on back side of top and hinged top over removed splash cover and cleaned old seal out replaced with new seal.Simple job but could not find parts locally and found Partselect on internet and ordered parts, very friendly and knowledgible person, ordered parts and had them in three days, would very highly recommend. Thank You Joe Lumpkin
Was this instruction helpful to you?
Thank you for voting!
Out of country repair needed
This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sheldon from Lacrosse, WI
- Parts Used:
- 5303279394, 131862900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
tub seal leak and belt tensioner pulley making noise
Removal was relatively simple, and pretty self explanitory as per the instuctions on the website, except for having to actually take sandpaper to the agitator shaft to remove the rust build up from many years of use.After getting the rust off, made it easier to remove the seal housing. Removed and cleaned the seal area and replace with the new seals. Everything went pretty well. Put in the new belt tensioner pulley and replace the covers. Ran the machine at medium load cycle. No leaks, no noise from the pulley. Runs like a new machine. The lady was really pleased with the results.
Was this instruction helpful to you?
Thank you for voting!