MXW121RBW0-23 Tappan Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bottom "Screw", which is the front leg of the washer was broken.
Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from DALLAS, GA
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
water filling in machine without turning on
I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oxford, MA
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
water not coming into machine fast.
we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing
Was this instruction helpful to you?
Thank you for voting!
Washer tub enables after end of spin cycles
Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Ketchikan, AK
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer would only let cold water in,then not fully cycle
Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Unionville, PA
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
over fill caused door to come open
removed top cover to access valve dissconnected hoses and wires then unscrewed valve and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from mayfield, NY
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
water over flowing, old valve stuck open.
Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.
Thanks PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Birdsboro, PA
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
hot water kept filling the tank
I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Ridge, MD
- Parts Used:
- 131398303
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
washer leaking
Popped the tub cover off....replaced with new one.
Thank you so much for a speedy delivery.
Thank you so much for a speedy delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Saint Louis, MO
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Hot water was not entering the machine, but cold water flowed smoothly
1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wing from Oakland, CA
- Parts Used:
- 131210200
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
leaking
Just took out the old one, replace the new one and clip it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Horseheads, NY
- Parts Used:
- 131398303
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tub cover seal leaks water.
Lift washer lid by jerking the lid up and open. Remove front panel by removing 2 screws at front bottom and guiding tabs out of slots. Locate tabs on tub cover and gently pry loose with a flat blade screwdriver or putty knife. Remove tub cover and inspect seal area for damage or debris. Replace new tub cover on tub and align and fasten each tab. Ensure that lid is securely fastened to tub by pressing top of cover down and visually inspecting that each tab is engaged with tub hooks. Replace front panel. Use anti-seize grease when replacing the 2 front panel screws. Use a small amount of petroleum jelly on the top lid spring clips before closing washer top. (The last 2 tips will help any future opening of the washer.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Kansas City, MO
- Parts Used:
- 134190200
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
No cold water supply
Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Fort Mohave, AZ
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Cold water was filling slower than the hot water.
Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pulled hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malcolm from Shelley, ID
- Parts Used:
- 134190200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front load washer continued to fill with water until door failed. Major Flood
Removed screws at back securing top panel (4).
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so far!
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so far!
Was this instruction helpful to you?
Thank you for voting!