SWFT73NN Speed Queen Washer - Instructions

it was easy to replace the element

Went on-line, used Youtube to diagnosed heater element problem, went online and PartSelect's name came up-- easily found the element I needed -- the price was so reasonable that I did not feel I needed to price repair. Ordered the part -- part came fast-- no hasles.

ordered and replaced heater element, did not fix the problem so ordered thermal fuse and cycling thermostat when it arrived installed them still did not work. Went to the next item on list thermal cutoff kit ordered it, when it arrived installed and BINGO!!! It works... $107.00 later a dryer that works!!!!!

Replaced the heating element. Everything copacetic.

I watched the video on utube first, and thought this is a breeze. I'm older and so getting down on my but in the back was what I thought was going to be the hardest part. I removed the screws that held the back plate. Once inside the back I removed the plugs to the heating element with plyers, and the little round thing with nut driver. Ok, what now the video showed where the element just lifted out, mine didn't it was totally encased in the housing. So I felt around to see what was holding it and found a little screw on the backside of the housing, which took some work, and the head lamp so I could see, finally after all that I got the little screw out. The housing for the element still would not come out. so I went back to the video, no help there because the housing on the video just came out and went together about halfway up the housing, mine didn't it was just one piece, so I came here to parts select site and read what other people had said regarding their dryer. I found the information I needed. Thank goodness. I removed the two screws in the front of the lent trap, opened the top of my dryer removed the little Hex nut that held the housing in place, then I went back and removed the heating housing, replaced the element. It was kinda tight, but it fit. I went back to the front put the hex nut back on replace the two nuts in the lent trap closed the top of my dryer, sat back down and replaced that little round thermostate thingy, plugged in the wires to the heating element replaced the back plugged it in and Oh Yeah I had heat. The experience demanded a "High Five" , I felt like a million bucks- this old lady did it herself and the hardest part was having the correct information and getting up and down off the floor. Thanks for all the help!

I replaced the heating coil and the dryer works perfect. Thanks for the quick service in shipping the parts to me.

Aser your instructions I ordered and replaced the elemateand now it is back to normal. Much thanks

Everything wears out with age. This is the second element I have replaced on this dryer. The time is fast approaching the dryer too will go the way side. For now, though, we just keep her going as best we can. Simple installation using simple tools. Safety first, unplug the unit. Make comfortable room to work on it from behind. Remove the back panel, push the top off and unscrew the retainer. Remove the bottom retainer screw and the two wires on the element itself. All you have to do now is lift the element case off the bottom bracket, remove the old element and replace with the new in reverse order. Viola! Be cautious of your new drying times. It seems a fresh element brings new life to drying your clothes. We have found it has been cut by more than a third time. As a side note; bring the shop vac out to suck away all the lint that accumulates inside. Fire hazard for one, deterant to life of machine also. You don't have to be an electrical genius either. If it comes down to that type of repair....Better call a repairman! =0)

Replaced Heating Element Works Fine Timed Dry Works Perfect But Auto Dry Has Heat Drys Clothes Fine But Won't Turn Off Dial Does Not Move Any Sugestions

Turn off and unplug dryer, pull dryer away from wall to allow a decent working area. Remaoved use multi meter to assure no current flow, disconnect wires/remove at contact points. Remove panels and screwsnto expose heating element. Continue to remove screws from heating element, the only problem I had was reaching the top screw the is on the inside. I was able to squeeze my hand through an opening with a short/stubby flat head screw driver.

There are adequate repair examples in the forum especially one with the video. Pick one that you are confortable with and follow the guidelines remembering where the screws came out of off and using the magnetice extender to hold the screws removed. The video on the site was very helpful - the delivery time by partselect.com was impeccable.

i wasnt down stairs when my brother did it he took it apart and put it back together. my brother know all about fixing things hes a machanic

With the power cord disconnected, of course, I removed the rear panel. I used an ohmmeter to check temperature switches and heating element. I did this by removing the wires from the switch, and touching meter leads to each terminal on the switch. When the reading showed 0 ohms, I knew the switch had continuity and was ok. There are three switches to test. If the heating element temperature switches are bad, then the heating element will not work. I found all switches to be ok. I then removed wires from element and tested. No change in reading when leads were touched to terminals. I removed the one screw that holds the heating element housing on and removed the assembly. Removed the element from the housing and checked the coils. I found a break in the coils. This sounds like a lot of time, but, it only took about 15 minutes to do all of this. The element only took a couple of days to arrive. I vacuumed all lint from dryer,installed the element,and assembled dryer in about 15 minutes. It works great. I think it took longer to find and order the part than it did to repair. The part, including freight , was about $30. That's a heck of a lot better than $500 or more for a new dryer! P.S. If you're worried about remembering where any of the wires go, just take a picture before you disconnect anything.

Remove the screws from back cover to remove it.
Remove the two philips screws of the filter on top of dryer, to open top cover.
Once open, remove the screw that holds the heating element housing.
Unplug the terminals from heating element.
Unscrew the heating element from its housing.
Replace the heating element.
Screw on the opposite way you disarm the dryer.