RTW4516FW1 Roper Washer - Instructions

I already had the old agitator out, so when I got the new one I put it in the tub. You have to spin it a little so it seats properly. I then tightened the bolt with a 7/16” socket and my wife was washing a load within 15 minutes

snapped off the softener dispenser, pulled out the plastic seal below and could see problem. Used socket with extension to remove agitator. ran machine to verify transmission was working.
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again

Super easy. Watch the video on YouTube.

Removed the attaching bolt and then removed the Upper Agitator Assembly. I removed the damaged parts and installed the Agitator Repair Kit and Re-installed the NEW Upper Agitator Assembly.

All of our wash was smelling like mildew. It was making us nauseas . After the repair everything smelled fresh and clean again. We received our parts within three days.

Thanks

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.

Replaced agitator sprage kit. Simple instructions simple repair

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

I removed the softener cup from the top of the agitator unit. The auger works separately from the bottom agitator. Remove the cap from down in the auger. There is a 7/16" bolt that holds the Auger and agitator to the center shaft. Loosen that bolt with a 7/16" socket on an extension from the ratchet wrench, and remove it from the bushing- I used a magnet. You will need to hold the agitator to loosen the bolt. Save that bolt. You will need it later. The entire agitator and auger can be lifted as a unit straight up out of the washer tub. There is a plastic bushing in the replacement kit. Slide it down over the center shaft with the small tabs up, then apply some Vaseline to the tabs as a lubricant. The new agitator can now be slipped down over the center shaft and seated on the bushing. Place the top auger onto the shaft down on to the agitator. Next, assemble the top bushing by placing the four cogs into the slots with the small pegs. The cogs must have the side with the raised area on the top of the assembly. Next push the plastic keeper down over the center of the bushing to hold the cogs in place and push it down to secure the cogs. Place this assembly into center shaft and line up the four rectangular holes in the top bushing with the four plastic prongs below. The top bushing assembly may be pushed down and secured by the four upright pegs below. If there are plastic tabs obstructing the rectangular holes in the top bushing , you can put the bolt back into the center hole and carefully tighten it down making sure the four holes align with the four pegs below. Tighten until the top bushing is securely in place. You will need to hold the lower agitator while you tighten the bolt with the socket wrench. Replace cap over the top bushing, then the softener cup into the top of the agitator assembly. The job is complete.

Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

Inserted a straight slot screwdriver into the small opening between the Fabric Softener Dispenser and the Agitator Assembly. Twisting the screwdriver slightly, causes the dispenser to separate from the agitator exposing a 7/8" bolt. Using the proper socket, removing the bolt allows for the removal of the complete agitator assembly. Reverse this process to install the new complete agitator assembly.

I simply watched the brief video supplied on both the page as well as my emailed receipt and performed the steps as directed. There were no deviations required... it was exactly how the video described it. Honestly, I expected a more lengthy and complicated repair!

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.