MAH21PSAWW Maytag Washer - Instructions

Thanks to Partselect's accurate parts' lists, and installation video, along with others' posted installation trials, gained confidence to attack problem on my own (coupled with repair (or should I say, "replace")men's advise to trash machine). Bearings had basically disintegrated, causing inner tube to be out-of-alignment, and rub against outer tube. Would just like to add to what others' contributed, that I found Plumber's Tub Drain tool to work very well at knocking-out larger front bearing (was perfect fit to ID of bearing). Had to Dremel cut out rear bearing, but quite accessible from rear of machine. Otherwise, alot of cleaning from 13yrs. of useage. Thanks for everyone's assistance!

I had pretty much the same experience as others. Difficult parts were 1) removing the inner tub, I used the blunt side of an axe with a 4x4 after several hammers would budge it. 2) removing the old bearing, like others I had to cut them out using a Dremmel with a steel cutting disk from Home Depot ($15) Wear eye protection as sparks are flying! Cut out the inner race and the bearing fell out, then cut V notches in the outer race, trying not to cut into the bearing seats on the tub although I did have a couple small cuts, then hammered it out from opposite side. Installed the new beaings and metal sleave between (what is the sleave for?). I tapped both bearing up against the seat shoulder but with the sleave in between there's not enough room and the new bearings turned real hard as the sleave is binding them. (Minor panic). A couple taps with hammer and chisel on the inner bearing from opposite side to push it out created enough room and the bearings turned real easy. Suggestion; plug the drain opening in the bottom of the outer tub with a towel or sponge to prevent pieces of the old bearing from falling in there. I saw one ball roll down in drain, so I tipped the machine on its side and several balls washed out plus pieces of the old bearing. I had a towel laying over the top but that wasn't enough, needs to be stuffed down in the opening. Re-assembly was easy and the machine runs perfect. The wife is very impressed. Total investment approx $85 (kit, bearings and cutting disk) plus about 8-10 hours vs $800 repair or new machine.

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.

Accessing the bearing housing was quite easy and the PartSelect videos were quite informative. Upon removing the lip seal the bearings obviously needed to be replaced. The bearings needed to be purchased from a local supplier and we used Grainger #6L028 (rear bearing) and #6L029 (front bearing). We needed to apply a generous amount of Liquid Wrench and used a long drive punch pin and a 3-jaw pilot bearing puller to remove the bearings. After removing the rear bearing we broked the puller on the front bearing, but were able to remove with the punch pin with the access created at the rear of the drum. Reinstalling the bearings was text book, we used a long bolt with large washers to pull the front and rear bearings together, with the spacer inserted between them.

Followed the PartsSelect video for the seal replacement, which was step by step and spot on, I just had to add the bearing replacement part myself. Once it was dissembled I drove each bearing out by tapping them with the hammer and drift. My model had no bearing retainer ring. I did not remove the outer drum from the washer. Clean the aluminum hub real well, scrape it with a utility knife to remove corrosion, wipe with a solvent soaked rag, etc. I disagree with other methods ive seen while researching, like a wire brush in a drill, because you will remove aluminum material from the hub and the bearing wont fit as tightly as designed. tap in the rear bearing til fully seated. I did the rear first because gravity then held the spacer in place. Set the spacer in place, noting that one end is "flared" to a larger diameter, so it seats against the larger race of the front bearing. Align and start the front bearing in place. The spacer needs to align with the bearings so it bears against the inner races of the bearings. So to hold it in place I rolled up a piece of light cardstock, slid it thru the spacer and bearing, and as it "uncoiled" it aligned the spacer. Pretty well. I did have to tap the spacer a little with the drift after the bearings were in, but just a little. After that, back to the video for the seal and reassembly. Only other comment I have is to locate the bearings early. I ended up going to grainger for one and Napa for the other. And no one could seem to cross the "DU" part of the original NGK bearing. The DU means it just has seals on both sides. Pretty standard stuff. That could have been easier. Also hold off ordering extra parts. I have found PartsSelect is really quick getting stuff out. I ordered an inner drum because i heard from other research that that could cause the banging noise. My banging noise was from one bearing disinegrating and the balls breaking up inside the hub. Shipping the drum back cost 70. UPS wanted 160. So that could have gone better, but I didn't want to let the machine sit too long. Next time I'll let it sit a couple days.

Removed tub replaced bearings. Put in new seal. Be aware drawing on instruction shows seal cup instaled from wrong side of seal. Other wise went well. Got bearings from McMaster Carr.

I was sick when I heard the noise from our washer. I looked online at new ones and found out it was going to cost between $1000 to $1500 to replace it. While looking online I found the PartSelect site. Unbelievable! I put in the model #, read the posts, ordered the parts and within a few days they were in. Using the video and the posted instructions I took it apart and replaced the bearings and seals. The whole thing took about 3 hours and we were back to washing clothes. Total repair costs were about $160 to $180. Compared to the price of a new washer, you guys saved the day.

The replacement was not complicated. It took me more time because the details are not in the videos and I had to do it twice because I didn't get the seal on correctly the first time. I used the Neptune videos available on you tube for the basics. Use the "inspecting front door lock wax motor" video for a start, but be sure to take off the top front crosspiece also for easier access to the spring that tensions the seal retainer cable. You don't have to disconnect any wires, just lay the door lock assembly gently to the left of the washer. The old seal comes off very easily, using the front loader door seal video. My washer was an early one without the drain tube so I had to get the drain tube and clamps separately and drill out the tub nipple to the left below the seal. I used the biggest drill bit I had that fit inside the nipple. The tub is plastic and very easy to drill. Most of the plastic shavings will come out toward you if you drill slowly and don't push too hard on the drill. I also used my shop vac to try and get out any other shavings. I used dish washing liquid as a lubricant to help put the seal on and used too much. It doesn't take very much. The spring that tightens the inner seal clamp/cable was very hard to attach and it did require two locking pliers [vise-grips] and quite a lot of effort. You have to hook one end of the spring to the cable that wraps around the seal, hold the other end of the cable with locking pliers, the free end of the spring with locking pliers, and stretch the spring to hook it to the free end of the cable. There are some other methods described in various forums and one of them might work better for you. When I was an auto mechanic we had a special tool that helped attach springs like this on drum brakes. I was sure wishing that tool was still in my tool chest but it was not. This was the most difficult part for me, getting the cable and spring all in place and stretching the spring without dislodging the seal and having to start all over.I didn't get the seal aligned correctly the first time and had to do it over after putting ever thing back together and washing a load of clothes. I could have avoided that by carefully inspecting the seal before I put everything together. When you put it back together the end of that red or green nylon line that looks like weed eater line goes under the soap/bleach dispenser bezel on the top so you can manually open the door if the wax motor goes bad and it won't unlock.

Following the information on the web it simplified this repair a great deal. Disassembled the front of the machine, then pulled it out from the wall, removed the rear panel. Removed the belt & pulley and knocked the shaft loose from bearings. Removed the tub and using the brass bar drove the rear bearing out first then removed the seal and front bearing. The seal has to come out first so the plastic spacer can be removed, used the brass bar from the rear of machine to drive front bearing out. Cleaned up all parts and reassemblied. Replaced the motor isolators and drive belt with new since I was in the machine that far. Removed the soap & bleach tray and cleaned up all those parts. re-assembled and washed a load of rags to test machine. Sounded like a new machine. Sourced the new bearings from a bearing supplier they are 6200 Series bearings, Rear 6206-2RS; Front - 6207-2RS. Had I not made this repair I would have been buying a new washer & dryer so this job for a little over a hundred bucks saved me thousands! Thanks to PARTSELECT for all this information!!

I referenced the enclosed instructions, and U tube videos, along with gasket I also changed the bearings for about $40. From local grainger, it seems to have solved problem, thanks for quick shipping,

Repair was simpl, took about 3 1/2 hours +. Used on line video for dismantal information & reassembling. Hammered out old bearings and seals. Installed them with big bolt and old bearings, I used the old bearings as pushing tools for new bearings. The large bolt and nut pulled the bearings in to place at the same time. Installed seal and reassembled machine. I moved from Jester to King at home.

I just replaced the pump.

I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!

I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!

Replaced the inside door panel. Who needs a Maytag repairman! Thank you for the great instructional video.