MAH14PDDWW Maytag Washer - Instructions

Followed the PartsSelect video for the seal replacement, which was step by step and spot on, I just had to add the bearing replacement part myself. Once it was dissembled I drove each bearing out by tapping them with the hammer and drift. My model had no bearing retainer ring. I did not remove the outer drum from the washer. Clean the aluminum hub real well, scrape it with a utility knife to remove corrosion, wipe with a solvent soaked rag, etc. I disagree with other methods ive seen while researching, like a wire brush in a drill, because you will remove aluminum material from the hub and the bearing wont fit as tightly as designed. tap in the rear bearing til fully seated. I did the rear first because gravity then held the spacer in place. Set the spacer in place, noting that one end is "flared" to a larger diameter, so it seats against the larger race of the front bearing. Align and start the front bearing in place. The spacer needs to align with the bearings so it bears against the inner races of the bearings. So to hold it in place I rolled up a piece of light cardstock, slid it thru the spacer and bearing, and as it "uncoiled" it aligned the spacer. Pretty well. I did have to tap the spacer a little with the drift after the bearings were in, but just a little. After that, back to the video for the seal and reassembly. Only other comment I have is to locate the bearings early. I ended up going to grainger for one and Napa for the other. And no one could seem to cross the "DU" part of the original NGK bearing. The DU means it just has seals on both sides. Pretty standard stuff. That could have been easier. Also hold off ordering extra parts. I have found PartsSelect is really quick getting stuff out. I ordered an inner drum because i heard from other research that that could cause the banging noise. My banging noise was from one bearing disinegrating and the balls breaking up inside the hub. Shipping the drum back cost 70. UPS wanted 160. So that could have gone better, but I didn't want to let the machine sit too long. Next time I'll let it sit a couple days.

The replacement was not complicated. It took me more time because the details are not in the videos and I had to do it twice because I didn't get the seal on correctly the first time. I used the Neptune videos available on you tube for the basics. Use the "inspecting front door lock wax motor" video for a start, but be sure to take off the top front crosspiece also for easier access to the spring that tensions the seal retainer cable. You don't have to disconnect any wires, just lay the door lock assembly gently to the left of the washer. The old seal comes off very easily, using the front loader door seal video. My washer was an early one without the drain tube so I had to get the drain tube and clamps separately and drill out the tub nipple to the left below the seal. I used the biggest drill bit I had that fit inside the nipple. The tub is plastic and very easy to drill. Most of the plastic shavings will come out toward you if you drill slowly and don't push too hard on the drill. I also used my shop vac to try and get out any other shavings. I used dish washing liquid as a lubricant to help put the seal on and used too much. It doesn't take very much. The spring that tightens the inner seal clamp/cable was very hard to attach and it did require two locking pliers [vise-grips] and quite a lot of effort. You have to hook one end of the spring to the cable that wraps around the seal, hold the other end of the cable with locking pliers, the free end of the spring with locking pliers, and stretch the spring to hook it to the free end of the cable. There are some other methods described in various forums and one of them might work better for you. When I was an auto mechanic we had a special tool that helped attach springs like this on drum brakes. I was sure wishing that tool was still in my tool chest but it was not. This was the most difficult part for me, getting the cable and spring all in place and stretching the spring without dislodging the seal and having to start all over.I didn't get the seal aligned correctly the first time and had to do it over after putting ever thing back together and washing a load of clothes. I could have avoided that by carefully inspecting the seal before I put everything together. When you put it back together the end of that red or green nylon line that looks like weed eater line goes under the soap/bleach dispenser bezel on the top so you can manually open the door if the wax motor goes bad and it won't unlock.

Using online disassembly instructions removed and replaced front and rear bearings. Then attempted to install the seal kit that was purchased online from partselect. Com. Was supposed to receive both seals plus lubricant so that no matter which seal I needed I would be covered. The kit I received had 2 seals that were identical. . . I needed, as it turned out the early seal kit, but unfortuneatly I had 2 revised kits. Of course I tried to assemble one but it just won't work. The seal kit must be the correct one. I didn't give up. I ordered another seal kit online from appliance partspros. Com and received both kits as advertized. . . One being the early version plus a small packet of grease along with all the other required loose parts and was able to complete the repair. The second time around proved much easier because of the experience factor.

Followed the instructions that were supplied with the Lip Seal Kit, for removal of the inner drum. As expected, once into the project, I found that the bearings that are part of the outer drum, were bad. Reading other installation blogs, prior to starting, I knew the bearing sizes, 6206-2RS & 6207-2RS, and I purchased the bearings, from Motion Industries, before starting the project. Taking a hammer and long 1/2" socket extension I was able to remove both the inner and outer bearings form the outer drum. (Bearings were all but seized up) Once I had cleaned up the aluminum hub which is part of the outer drum and where the bearings mount, I was able to start the process of installing the new bearings and completing the project. Timing could not have been any better to take on this repair project because the aluminum hub was showing major signs of corrosion on the inner side of the hub. I was concerned that the new lip seal would not seal off the inner drum from the bearings/outer durm. This project was competed on 8/21/12 and so far and 6 loads later I have not found any leaks.

I went on your site and found out the Bearings were not sold separately by Maytag and that they wanted $800.00 for the entire outer tub in which the bearings are pressed into. I read another post on your site where someone referenced some NSK bearing part numbers. I went to my local auto parts store that cross referenced the NSK number to Timken Bearings (a high quality automotive bearing). Following the instructions I hammered out what was left of the old bearings cleaned everything and pressed in the new bearings. When the Lip Seal kit arrived I pressed in the new seal following the instructions provided, reassembled the washer and it’s as good as new. Total cost just over $100 in parts and a few hours labor. Removal of the old bearings was a difficult task especially since mine were in such bad condition as water must have been slowly leaking into them for some time. If you have some basic automotive repair skills and or some knowledge of how to remove and replaced pressed in bearings I would recommend this repair. In my case money was the motivating factor with 2 kids in college and a wife who would have insisted on a new matching set of a washer and a dryer instead of just replacing the washer.

The whole thing is on YouTube beating out bearings was the only difficult part

Removed tub replaced bearings. Put in new seal. Be aware drawing on instruction shows seal cup instaled from wrong side of seal. Other wise went well. Got bearings from McMaster Carr.

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.

Being a seventy five year old man I was reluctant to taking on this job but after getting prices for the repair or replacing the machine I cringed and trying to save some money I took on this job.Got all the information I could find on line I got started.Taking machine apart was easy and remembering to keep parts separated is something I learned from my mechanical back round is a must.Pictures also help.Taking out spinner drum easy.Bearings a nightmare If you don't have a bearing removal tool.Front bearing had to be cut out with a dremel tool and zip wheel being careful not to destroy the race.Removed spindel from spinner drum as I could see that for me to put shaft in hole would have been a problem.Put new improved seal in.Easy part.Reassembled. Springs and clips hard.Washing again and quiet.Wife happy four days later.Old guy sore.All done with outer tub in machine.Estimated savings Big,Big,Big.Getting big steak dinner and big kiss.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

First and foremost, disconnect the power before anything else, then remove the door, access panel, and front of the washer,I then detached the front of the rubber boot so I could remove the plastic panel that it attaches to, that exposes the springs, I then used a vice grip to remove the springs replacing them one at a time, I also replaced the struts in the rear of the machine which requires removing the rear panel, and I used a bottle jack to support the rear of the washer tub while I changed the struts, I changed the struts first which only helped a little, the springs made the job complete and the washer now completely wrings the clothes to a damp state that dries quickly.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

Followed the video, besides the spring, everything was easy.