3LMVWC100YW0 Maytag Washer - Instructions

Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!

Just follow the video! Very easy.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

The old part popped right off, and new one installed. Works Great!!!

The info. was really helpful

Super easy. Watch the video on YouTube.

Replaced agitator sprage kit. Simple instructions simple repair

Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

Gravy replacement! I pulled out softner dispenser,
undid the one bolt securing the agitator assembly, and removed the top half of the agitator. the cam assembly tapped out. I replaced the bolt so I could still use the machine while the parts were on the way. When the part arrived (36 hours later with 3-5 days expected) I removed the bolt again and followed the simple instructions to replace the cam. Saved a ton on repair costs!

I am a maintenance mechanic and was very easy for me. I just loose i screw 10mm took out old parts put new parts in and it was ready to go again.

I removed the fabric softener dispenser atop the agitator. I twisted and pulled out the plug inside the agitator. Using a socket on an extended wrench, I removed the single nut inside the agitator (keep the agitator from turning with a large screwdriver, etc. and turn the nut counter-clockwise to remove). The agitator came out, and I removed all of the cam parts. I cleaned all of the old parts with bleach and water. Reinstalling the new parts was simple and straightforward as indicated in the illustrated instructions. Now it works great!

I popped the cap off the agitator removed a bolt. Removed the damaged parts. And replaced them with the new ones it was easy.

The most difficult aspect of the repair was separating the upper and lower agitator, as over the years the minerals in the water had stuck them together. I used a rubber mallet and gave the auger a few sharp blows, and the two main pieces separated. The greatest amount of time involved was the process of meticulously cleaning all the parts that were to be reused in the repair as there was a lot of old grease, dirt and mineral build up coating everything. The old cam dogs were completely gone, they had disintegrated over 20 years of use. I simply dropped the four new dogs in their cut outs on the cam agitator. and snapped on the bearing collar, which is really just a plastic retaining ring that prevents the dogs from falling out when you turn the cam agitator upside down and push it into position to connect the two agitator sections. The new thrust washer easily set in place on the lower agitator, and bolting the assembly back onto the washer shaft was a snap with a 10 inch socket extension. Washer works perfectly now, it spins better than the average political pundit.

Easily found the Agitator Repair Kit online for a very reasonable price. Swapped out the bad worn down parts for the new ones and presto; cleaner clothes. Researching the right model number was a task, but when the parts showed up and were identical I knew it would be easy. Less than 30 minutes to install with minimal tools. And it was cheap. Even if I called my home warranty co. to come out it would still be a minimal $55 service charge. Well worth it, very pleased, would use PartSelect again.