PVTEST2Q Maytag Washer - Instructions

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

I was sick when I heard the noise from our washer. I looked online at new ones and found out it was going to cost between $1000 to $1500 to replace it. While looking online I found the PartSelect site. Unbelievable! I put in the model #, read the posts, ordered the parts and within a few days they were in. Using the video and the posted instructions I took it apart and replaced the bearings and seals. The whole thing took about 3 hours and we were back to washing clothes. Total repair costs were about $160 to $180. Compared to the price of a new washer, you guys saved the day.

I went on your site and found out the Bearings were not sold separately by Maytag and that they wanted $800.00 for the entire outer tub in which the bearings are pressed into. I read another post on your site where someone referenced some NSK bearing part numbers. I went to my local auto parts store that cross referenced the NSK number to Timken Bearings (a high quality automotive bearing). Following the instructions I hammered out what was left of the old bearings cleaned everything and pressed in the new bearings. When the Lip Seal kit arrived I pressed in the new seal following the instructions provided, reassembled the washer and it’s as good as new. Total cost just over $100 in parts and a few hours labor. Removal of the old bearings was a difficult task especially since mine were in such bad condition as water must have been slowly leaking into them for some time. If you have some basic automotive repair skills and or some knowledge of how to remove and replaced pressed in bearings I would recommend this repair. In my case money was the motivating factor with 2 kids in college and a wife who would have insisted on a new matching set of a washer and a dryer instead of just replacing the washer.

The video was great. The only problem was getting the spring back on. It was way too stiff, so I put it in a vise and stretched it a bit. It's a bit fussy but your site made it go pretty easy. thanks

I lifted the lid, removed the front cover and then twisted the pump in its mount. The pump came out of the mount and i put a pan under it. I unscrewed the two clamps then pulled one end out. Water spewed everywhere and it was a bit of a mess. I pulled out the two wiring harnesses and pulled out the pump. It had a key, a quarter and a nickel in it. I had not seen the key in years! I put the ground wire on the new pump and then the main wiring harness. I put on the power wires but later had to take it back off, so do this later. I then attached and tightened the clamps. I put the pump in the mounts and then twisted it into locked position. Then i put on the power line. I put the cover back on and tested it, all good. I saved a lot of money, about $300 between the initial service call and second trip to install it. I like this washer because it gives you problem codes. It is 14 years old, and this is its second breakdown. First time was the PC board under warranty. No problems for 12 years, which was caused by leaving coins and keys in the pockets of my clothes.

Follow the suggestions on the rope tied to the side of the washer, then mechanically lever the spring open. Only change I would incorporate is using a block of wood to keep the wash drum from moving over as you pull on the rope to open the spring up. GREAT AND EASY FIX!

Set my iPad on the dryer and played the video. Could not have done it without it. Putting spring back on was the hardest, fell off once. Took that long because video connection timed out and had to get another coffee. Part delivery was quick. Found the drain tube out of the bellows was clogged. If it wasn't for the mildew on the bellows could havw fixed the problem if I had known about a drain at the bottom of the bellows.

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

Followed the video, besides the spring, everything was easy.

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

Replaced the belt and motor isolators. Watching your video made it very easy.

The repair was very easy after watching the video that was with the part. I will continue to use this site for other repairs that need to be done.