PVTEST2Q Maytag Washer - Instructions

I haven't finished the job yet. I was very surprised and very happy with how fast PartSelect got my part to me. I ordered a lip seal kit (maytag neptune bearing replacement) in the morning, and the very next day it arrived at my door. I'm very impressed. I have everything cleaned up and ready for the new parts. I just have to finish.

Thanks for the speedy service. I'll be highly recommending PartSelect.

Frank

my husband took the old part off. order the new part thru your company...3 days later the part came in. then he reattached thee part to the hoses with the champs and we said alittle pray and i had my washer back

I followed the extensive instructions others had posted on this site about the need to replace the "non-replaceable" bearings. The hard part is getting the old bearings out of the outer tub as they were very corroded. I left the outer tub in the machine and after attempting to beat them out unsuccessfully, I resorted to using a Dremel tool with a small grinding disc on the end to cut the bearings apart, first cutting through the center and removing the ball bearings, then cutting through the outer rim and edge being careful not to cut to deeply, once the bearings were weakened, they came out pretty easily. Installing the new bearings and putting the machine back together was pretty easy. The machine works like new, so for me it was well worth it, thanks to everyone who shared their experiences so I felt comfortable giving it a try!!

Removed washer back panel (after unplugging unit). Installed new belt. Reinstalled back panel. Belt wAs very tight getting it to roll onto the drum.

First of all, let me say that the Lip Seal Kit was delivered the next day after my order and that I was encourged to attempt the repair by the owners repair procedure response. The lip seal in my machine must have failed along time ago as I have been living with noisy bearings for at least the last twelve months. Disassembly of the machine was straight forward following the Part Select instructions. The lip seal was so disintegrated it hard to tell what originally looked like. Lots of rust and gunk in lip seal area. After removing the snap ring behind the rear bearing I was able to drive out the rear bearing using a brass 3/4" drift pin and a two# hammer. I than attemped to remove the front bearing using a 1 1/2" steel pipe that matched up to the inner race of the front bearing and my trusty hammer. Nothing I did could budge that bearing. Since the outer tube is suspended by springs and struts I decided that lot of hammer energy is absored by springs and my best solution was to remove the outer tub. I then used a couple pieces of U channel steel(this could be steel pipe or some 2X4's) that were longer than the depth of the tub and positioned them to contact metal bearing tub insert. These supports were mounted in small Workmate vise setting on the garage floor and using the 1 1/2" steel pipe I drove the inside bearing out. After some general clean up I picked up some bearings at the local distributor for $42.00. Re-assembly takes a little planning as you need to hold the steel insert betwwen the bearings and keep it lined up in the bore. I think the best way is to install the rear bearing first and install the snap ring. I then put the steel ring in place and held it with cardboard insert from a paper towel roll. The cardboard roll was cut about 2 1/2" long and cut lenght wise to insert though the rear bearing and held in place with tape. The front bearing was then tapped into place followed by the lip seal. Note that if you install the front bearing first and seat it all the way in, the rear bearing will contact the steel insert and not allow enough room to get the snap ring in place. When I was done I didn't have any parts leftover and thru six washing machine loads peace and quiet has returned to my house. Hope it last. Note: If you elect to remove the outer tub you might want to take some pictures so you can see how it all is supposed to look before you close the hood.

I researched the internet and found my answer on this site. There were others who shared their experiences which made the repair easy. There was a leak in the front gasket between the drum and outer frame. I printed out several answers that customers had posted. I opened the front door on the washer and found a tear in the bottom of the gasket near the drain hole.
To use the washer until the parts arrived (which only took 2 days), I used a bike repair patch to seal the hole in the gasket. NOTE: Don't use the glue type as it may get on the clothing. I used a patch that you pull off the backing and apply. It worked great until I got the parts.
Another party had posted how he got the cable and spring attached on the gasket. He used fishing line. I used masonary string I got from Home Depot. I made a loop on one end and attached it with the spring and pulled both around the gasket after I had positioned it on the back drum. I looped the string over the other end of the spring and pulled. As the spring stretched, I hooked the other end of the cable on the spring. It worked perfectly. Note: Don't worry about the string being underneath the cable, you merely pull it out slowly and the hard part is done. I then hooked the front of the gasket into the slots and finished the job. It took about 40 minutes alone.
P.S. Parts select got my ordered filled and sent to my residence within two days. Great experience and I would not hesitate to order from them again.

I removed the screws (as they became accessible) from the following items with screw driver or nut driver:
1) door
2) hinges
3) hinges vanity plug on the other side of the door
4) front panel

I then
5) unplugged the washing machine
6) turned off the hot and cold water
7) removed the hoses and hung them up to avoid water on your floor (have mopping cloth available)
8) Removed the detergent and softener storage pockets
9) Opened the top of the washing machine.
10) pull out internal hoses away from the water valve
11) Removed spade electrical clips from the valve.
12) Wiggle away the valve and remove (if screw is present removed it as well)
13) Put in the new valve and reverse the process back to item 1.

It appears that there was mineral deposit on the valve and I am not certain if it clogged up the valve or seized it .

Using a screw driver I removed the 4 screws that hold the front panel and door on allowing me to remove the front panel and door. I removed the spring clamp from the drain hose and removed the drain hose. I removed the 4 screws holding the detergent access door on the top and removed the door alllowing me to tilt the top up and back. Now both sides of the seal were exposed. The front side of the seal is easily pulled loose and the back side is held on with a cable and spring tensioner. The spring and cable slipped of freeing the seal. I installed the back side of the seal paying attention to the alignment "ticks" in the seal and washer. I installed the cable assembly and spring using pliers to pull the spring into place. The front edge was pushed into place. I installed the drain hose and spring clamp, lowered the top into place, installed the detergernt access door with the 4 screws, and installed the front panel and door using the 4 screws. The only trick wwas getting the back edge spring tensioner in place. It took 3 tries over ~ 10 minutes. All other items were very easy. I watched the first load wash to be sure the seal did not come off.

I took off the front cover, lifted the top, removed old door latch assembly and replaced wire for wire; put the washer back together. The part came in great time and it was a no-brainer. The appliance repair man sold my wife a bill of goods and basically lied to her. Word to the wise, "An appliance repairman who can come at your calling is one to be careful of, most good repairman are busy and it may take a day or two come over."

It was very easy to do. I took the back cover off. I dissconected two hoses. disconnected one wire. removed a small plastic bag (cover over wires). turned the pump 1/4 turn.and reversed this process with the new pump. It took me 15 minutes to remove and replace. Put the washer thru a cycle and it worked!

I replaced the boot seal. I unscrewed and took off the front door and front panel; I unscrewed and removed the detergent compartment; unbolted and lifted up the top panel. I removed the old worn out gasket and replaced the anterior (door side) portion first, then the posterior portion. the door side pushes right in by hand but I used a putty spatula to firmly seat it evenly in place. For ease of closing the spring loaded wire on the posterior portion of the gasket, one person held one end of the wire and gasket in place and a 2nd held the other side in place and pulled the spring with pliers to connect and seal the gasket. replacing the boot seal requires 1 person, but having a 2nd person around to help with the spring was helpful. this was an easy project that takes about an hour.

First I removed front and rear covers and the dispenser screws. If you are carefull you can fold the front cover back and lay it on top of the washer so that you do not have to unplug all the wires. Remove the clips on the front of the outer drum with a small flat blade screwdriver and set aside. Go to the back and roll the belt off the pulley. Remove bolt and snap ring and the pulley should pull toward you off of the shaft. This is plastic be carefull. The inner drum will now pull out thru the front of the machine. Now read the directions again and again about the seal because you have to replace exactly what you take out. This is my only complaint with the directions there needs to be a picture and not an illustration of the placement of the sael and the spacer in my case.

I removed the 2 screws holding the door and then the balance of the screws holding the front section on. Removed the trim piece and then the screws holding the detergent tub and top of the washer. Once the boot was exposed I used two pair of pliers to hold either end of the retainer strap and pushed together to relieve the spring tension. Then disconnected the drain hose from the bottom of the boot and removed the boot. Re-assembly was just a reverse of the disassembly and much easier than I anticipated. Placing the boot around the fron of the tub was like putting a bycycle innertube on a rim. Once you get it completely on then you place the retainer strap around the boot and attach by hooking the spring to one end and pulling the spring toward the other. (better if two people do that part but can be done by one) The front of the boot slides into the slots fairly easy and then you simply re-connect the drain tube in the front of the boot and reassemble the cabinet.

easy remove the front panel it just pops off unscrew the top and lift up. you have a few pieces to remove then press the old rubber out and install new, i had a little trouble lining up the hardest part was putting the cable ban back on with the spring, i needed help from a friend. now the tub seal was not needed but with it apart I went ahead and changed it the clips were hard to snap on,:you need strong fingers to do that! reassemble as you took it apart. washer works fine no leaks, and alot cheaper than a new washer. thanks to parts select for the right parts MICK KEATING

On the Maytag front load washer, we found the easiest way was to unscrew and lift the top of the washer up, then take off the door, and front panel. Removing the old seal (moldy) was easy, but to replace the new one you need to see what you are doing. (Reaching up blindly to slip the new seal around AND connect the spring, is near impossible.) It was not hard to do...IF you can see what you are doing. You need access to attach the drain tube, make sure the gasket is slid in place (with notches in line with openings) slip the cable around and attach the spring. Everything is easy IF you can see what you are doing (and a little muscle to pull the spring and connect it).