MHWE500VW10 Maytag Washer - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

I started by dismounting the door from the washer, then placed the door on a flat counter with a towel underneath to avoid scratching. I unscrewed all the bolts securing the the frame. Once the frame was removed, I dismounted the broken door hinge and secured the new one in reverse order. Just a little time and patience. Job completed with no mess!

repair was a cake-walk with the video there to help.Thanx

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

Replaced water pump

I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!

Removed top of washer and replaced flow meter.

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks