MHW8200FC0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from LAKE STEVENS, WA
- Parts Used:
- WPW10605427
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Error Code F01 E09 (Drain Issues)
Unplug appliance. Remove the back panel with the 1/4” nut driver and cordless drill. The pump is located as you face the back of the machine on the bottom. Remove four screws that hold pump in. Reverse the process and install new pump. Check the filter and clean out the housing.
Reinstall back panel and plug back in. Run a test load (no clothes) and test drain.
Reinstall back panel and plug back in. Run a test load (no clothes) and test drain.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Ardmore, AL
- Parts Used:
- W10763470
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Had to install shipping bolts so we could move the washer
Really was not a repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Lodi, CA
- Parts Used:
- WPW10110225
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
F/H error
I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooked the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Norman, OK
- Parts Used:
- WPW10110225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water flow problem resulting in f20 error code
Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANICE from MANHATTAN, KS
- Parts Used:
- WPW10110225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
I was having the hf code constantly beeping and couldn't run a full cycle.
I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lou from stamford ct, CT
- Parts Used:
- WPW10110225
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
HF code durring cycle
Removed top of washer and replaced flow meter.
Was this instruction helpful to you?
Thank you for voting!