MVWC300XW2 Maytag Washer - Instructions

I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.

I removed the cap over the ratchet mechanism, removed the ut holding the agitator in place, removed the agitator and cleaned all the parts. The assembly for the ratchet dogs was a 3 piece assembly that was included in the kit I bought from Part Select. I also bought a new cap and gasket since my old gasket had broken too. A new gasket was already included in the kit, so I didn't need ot buy the cap. I liked that th ekit included everything I needed and good instructions. parts got to me in about 3 days. Very happy with my Parts Select experience and the fact I saved at least $100.

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

I just ordered the complete agitator kit since I didn't know for sure what I all needed, and it made my repair so easy replacing since it was all complete. I followed video which was a great help. Got it all done in 25 minutes. Very easy. Thank you...

1. Removed the fabric softener dispenser

2. Removed Barrier Seal Cover

3. Removed bolt and seal

4. Removed and replaced CAM Agitator Assembly

5. Reversed the removal steps.

Had to clean out area where bolt was to go as it was full of debris. Placed agitator on, bolted on , placed softener dispenser on. Done

My husband just took the bolt in the middle took the broken one, put the new one, put the bolt back the lid the rubber seal and done. Working like new.
Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.

Took ten minutes to pop upper assembly off and replace dogs. Note long ratchet or nut diver advisable 5/8.

Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.

I already had the old agitator out, so when I got the new one I put it in the tub. You have to spin it a little so it seats properly. I then tightened the bolt with a 7/16” socket and my wife was washing a load within 15 minutes

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

The old part popped right off, and new one installed. Works Great!!!

I popped of the fabric softner dispenser at the top auger by appling pressure with both thumbs rather than use the notch provided. This gives access to the agitator mounting bolt which was removed with a deep socket and extension on a ratchet handle. The agitator slipped right off the splined shaft by pulling upward at two points at the bottom. I ordered the complete agitator repair kit which included a part that improved the operation of the top auger, it may have been a factory upgrade at some point on this machine. I did use silicone grease where required and I feel that this is a must for longevity of the thrust washer. If you are ordering the complete kit, the o-ring seal for the inner cap is included. The machine washes like it was new.

Ordered the inlet assembly from this site. Received it the day after I received the notice it shipped. Watched their video of how to replace the part. Easy job, done in 15 minutes. Only needed a screwdriver to take the cover off the back of the washer control panel. A company wanted $400 to replace the part.
Definitely recommend the company and will use again.

First removed the cap, took out the screw, pulled out old agitator and replaced it with the new one