4GMVWC300YW1 Maytag Washer - Instructions

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

Removed the old hoses and screwed on the new hoses.

Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.

the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23

I popped of the fabric softner dispenser at the top auger by appling pressure with both thumbs rather than use the notch provided. This gives access to the agitator mounting bolt which was removed with a deep socket and extension on a ratchet handle. The agitator slipped right off the splined shaft by pulling upward at two points at the bottom. I ordered the complete agitator repair kit which included a part that improved the operation of the top auger, it may have been a factory upgrade at some point on this machine. I did use silicone grease where required and I feel that this is a must for longevity of the thrust washer. If you are ordering the complete kit, the o-ring seal for the inner cap is included. The machine washes like it was new.

Removed the attaching bolt and then removed the Upper Agitator Assembly. I removed the damaged parts and installed the Agitator Repair Kit and Re-installed the NEW Upper Agitator Assembly.

All of our wash was smelling like mildew. It was making us nauseas . After the repair everything smelled fresh and clean again. We received our parts within three days.

Thanks

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Super easy. Watch the video on YouTube.

snapped off the softener dispenser, pulled out the plastic seal below and could see problem. Used socket with extension to remove agitator. ran machine to verify transmission was working.
Looked up parts on line and found Part Select. The repair stories insured me I had correctly identified problem. Ordered part on Sat. arrived Tues. Reversed disassembly process with new agitator. Success
Great source of information, fast delivery, very satisfied overall and will reccomend and use again

take off top on middle section (pops off) pop dispenser on--done

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

I popped the cap off of the agitator. I could see the grabbers weren't grabbing the side of the agitator. I thought I could take a shot at fixing it since I was ready to give up. Happened upon this site. With the model number, I was very easily able to find the parts I needed. Ordered them up. Took one bolt out of the assembly and the whole agitator came off. I popped in the new parts as the diagram was very easy to follow, resecured the bolt, and all was good. I saved a ton of money off replacement or even calling a service tech. Your site made this very easy with the detailed diagrams. Didn't order anything I didn't need. Only cost $11 to fix it and made me feel like Mr. Fixit. I will definitely use your site as my first, best choice for any problems I have in the future.

took out old agitator and installed new one, machine now runs like new. couldn't be happier.

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

7/16 socket removed nut and very easy to take apart replaced agitator. Spring knob just pop in. Awesome doing it myself and not having to spend over a hundred dollars to get a $20 job done!