4GMVWC300YW0 Maytag Washer - Instructions

the first order was ordered wrong for me and the part was to big so I had to send it back and order another. The second dispenser was the right one and went on well to the machine. Just had to put it on the machine by hand.

Per instruction sent with purchase

I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.

I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job

I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.

Machine works great now.

Pulled up on fabric softener dispenser and removed it. Had to use pliers to remove cap and seal to get access to the bolt holding the agitator in.

Realized my socket extension wasn’t long enough so went to Lowe’s and bought another.

Was unable to hold the bottom of the agitator to keep it still and get enough leverage to remove the bolt. I poured hot water over it and then climbed into the washer and used my foot to hold the vanes still while I removed the bolt. Once I got the agitator out, the rest was a breeze. Separated the top of the agitator from the bottom by placing it on the floor, using my feet to hold it down and pulling up to remove the top part of the agitator.
Turned the top of the agitator upside down and removed the cam and feed dogs. Assembled the new one and held the agitator top horizontally while placing the new part back in.
Reassembled the top and bottom of the agitator and put it back into the washer. Tightened the bolt, replaced the cap with its seal and pressed the fabric softener dispenser back into place.

Remove top of washer suspension
Rod goes on side of tub .

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Had to clean debris on metal drive shaft splines in orderv forvnew lower agiitator to seat properly. Install upper agitator and parts then reinsert bolt in upper agitator. Install cap and o-ring, fabric softner dispenser and test for proper operation.

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

I needed an air impact wrench to remove the single nut. It was stuck on there. Once the Nut. Was removed it was an easy repair. Perfect fit! Just pop it on the shaft and replace the bolt. Since I had my air tools out already I gave it a couple of dugga duggas.

Took off water softener from top of agitator. Pulled up and removed cap with O-ring that covered bolt that held agitator in place.then pulled briskly up on entire agitator from the bottom to remove agitator from machine.After that I put my feet on bottom of agitator and then pulled up on top part to separate the two pieces. After that just follow instruction sheets for parts replacement and then reverse steps to reassemble.

Exactly as shown in your video

Tightened up the pulley as the video showed me that might be the issue.

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!