BA283 Maytag Washer - Instructions

Removed the front panel. Then blocked up the front of the machine. Removed the pump belt. Removed the 3 5/16" screws from the bottom of the old one and tilted it slightly to remove. Put the new one in and reinstalled the 3 screws. Put the belt back on and slid new pump all the way to the right and tightened 1 screw. Loosened the screw until there was about 1/4" of gap when squeezed the belt together. Tightened the one screw, then the other 2. Put the front panel back on and lowered the machine. New pump works great.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Level the machine.

Very easy. Pulled a few wires and replaced them on new timer.

To troubleshoot the problem I removed a panel/blank from the back of the machine. I then started to fill the tub while watching the pump. It immediately leaked from the shaft seal. I ordered the part early the next morning. It arrived late the next day. I was able to remove the front panel of the machine by removing a screw at each front corner of the bottom of the machine. The pump was attached with three screws which were simple to remove. The pump was an exact replacement and fit identically to the original. I tensioned the belt, and tested the machine. Before reinstalling the front cover, I cleaned the interior of the machine a bit and replaced a couple of hose clamps whose steel screws had started to corrode. All in all a simple repair.

I tipped the washer up on 2by4 blocks used 1/4 inch rachet with 5/16 socket two remove 3 screws and the belt from underneath. Took clamps off hoses yahoo saved l00 bucks!

Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.

Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

The hot water select broke. The item was easy to find and order on your site. The part was easy to install. Will order from you again if parts are needed.

I propped up the machine. Turned the water off .took the pump belt off, then took the two hose clamps off. With a bucket and towels on hand for left over water in the hoses, i removed the two hoses. Then removed three screws that held the pump on. Installed the new pump in reverse order.

Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.

I replaced the 3 screws because they were rusty. Then I replaced the Drain pump

Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .