BA283 Maytag Washer - Instructions

Firstly, remove ac power from washer!
After removing the front panel of the washer (two philips screws), I loosened and removed the plastic motor cover and removed three hex head screws holding the motor. Have someone help you tilt the washer so you can remove the belts by "rolling" them off of the pullies (pump pully and motor pully). What I did was use a chemical degreaser to clean the motor base metal channel where the nylon sliders reside. After doing that and letting it dry, I removed the two old
springs. I ended up reinstalling the old springs because they were not stretched and I installed a new spring (total three) on the right side of the mount. A stiff metal rod with a hook on the end will help you install the springs. Squirt some of the included silicone lubricant on both sides of the motor mount channel and exercise the lube. Reinstall the motor and plastic cover over top of motor. Clean hands and clean belts while you have them out, reinstall belts and front cover and you're finished. My wife said it never ran better!

I loosened three screws to relieve the belt tension and removed the belt from the pump drive pulley. After removing the water from the wash tub I removed the intake and output hoses from the pump. I next removed the mounting screws and removed the pump. I attached the new pump loosely and re-attached the belt. I moved the pump to tighten the belt tension and tightened the mounting screws. I re-attached the hoses, filled with water, checked for leaks and replaced the front panel.

I took out the two screws in the bottom front panel of the washer, and rotated the front panel from the bottom away from the machine until the top or the panel was released from the machine frame. I then tilted the washer back to get access to the bottom of the machine. The pump pulley had split in half, and the bottom half fell off the drive motor shaft. The only problem I had was breaking free the set screw that holds the pulley to the drive motor shaft. I used a long arm Allen wrench and an adjustable "Cresent" wrench to apply enough force to break the set screw loose. Iclamped the upper transmission belts tightly to keep the motor shaft from turning while I loosened the set screw.

I was told that it might be a clog in the tube.. we check the tubes that wasn't it Then I Google it and was told it might be the drain pump. I was just glad that Part Select had what I need because my machine is over 20 years old. We change the pump and now I hope I get at least another 20 years out of my machine. I will always use part select to get my parts. Thanks

Make sure to release the springs and pulleys before you try to tackle the bolts that hold the motor base to the bottom of the washer. Mine were a bit rusty and took some force to break loose. Also it's a good idea to take pictures of how everything sits before you disassemble as the pictures in the repair kit are not very clear. Other than that it was pretty straight forward. Wiring was a breeze. . . . Good luck

Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.

I followed the supplied directions to remove covers, unbolt tub springs, and expose the area needed to replace the damper pads. I cleaned the area with acetone and applied a rubber adhesive (not supplied). I used tire patch compound because that is what I had on-hand. I positioned the pads and after they had dried 1/2 hour, lubricated them with the supplied grease. I reassembled the washer and it is now smooth and well behaved.

Tilted the washing machine back at 45 degree angle. Removed three screws from the underside of machine. Slipped belt off pump. Lessened two hose clamps and removed hoses.
Lifted old pump out. Dropped new pump in place.
Screwed in the 3 screws. Slipped on the belt.
Attached two hoses. Tightened hose clamps.
Set washing machine upright.

No more leak.
My problem was I could not prove the pump was the source, but after switching it out I have had no problems (good enough).

By doing the work yourself, not only gives you the good feeling you did it yourself and works just like it was when it was new and to know there's part's you can still get from part places like these! Like I say to my wife ( if they meaning a repair shop can do so can't I ). Course changing a motor in a car that's a different story, I'll let someone else to do that. To do the repair I took off the front cover of the washer exposing the tub, motor and other things. But the very first thing I did is unplug the power ( I hate the bad storys that if I only turned off the power ? ) then I took off the cover over the motor and changed the switch. And all in reverse. And plug power back in. Started up just fine.

took washer into the garage, removed front cover & disconnected the wiring. Then i removed the motor assembly. Piece of cake to finish job.

The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.

Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.

Took front panel off. Ran machine. Pump is see-through. Could not see any "aeration" of the water in the pump and no water was coming out of drain hose. Disconnected electric. Disconnected hose from drum to pump(first emptied ALL water from drom)and drained in bucket. Disconnected drain hose from pump to drain and drained any water. Checked for obstructions in hoses. Removed pump. Checked belt (was fine after 14 years). Ordered new pump. Received the next day! Replaced pump and tighten belt. Connected hoses and test it. All OK. Replace panel and did laundry.

Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).

First I unpluged the washer and then I removed the 4 tops screws from the washer front control panel and laid it down on top of the washer lid. I then removed the wires from the current switch and attached them to the new switch making sure they are attached to the correct push on terminals. I then removed the two screws holding the old switch, removed the old switch, seated the new switch and screwed it back in place with a socket wrench. I then put the front panel back in place and scrwed the 4 screws back in place. Took less than 15 minutes. While the switch works fine my problem is still not fixed. I had alrealy replaced the timer switch and how the temperature switch. I still need to figure out why the washer value does not open to let cold water into the tube after it finished the wash and empties the wash water.