7MMVWC100DW0 Maytag Washer - Instructions

I used a jack to lift the tub and unhooked the rods and replaced them. Works great.

Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

Ordered the agitator repair kit and it came very fast.. Followed the instructions, the kit had all the parts needed.. Took around 30 minutes, but some of that was scraping the built up scale from the agitator itself, you might not have to do that.. Easy job.. Agitator now works like new.. Very Happy, and so is my wife, the kids looked and said, "Hey,my jeans go down to the bottom now, cool..!!"

I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

7/16 socket removed nut and very easy to take apart replaced agitator. Spring knob just pop in. Awesome doing it myself and not having to spend over a hundred dollars to get a $20 job done!

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

I popped the cap off of the agitator. I could see the grabbers weren't grabbing the side of the agitator. I thought I could take a shot at fixing it since I was ready to give up. Happened upon this site. With the model number, I was very easily able to find the parts I needed. Ordered them up. Took one bolt out of the assembly and the whole agitator came off. I popped in the new parts as the diagram was very easy to follow, resecured the bolt, and all was good. I saved a ton of money off replacement or even calling a service tech. Your site made this very easy with the detailed diagrams. Didn't order anything I didn't need. Only cost $11 to fix it and made me feel like Mr. Fixit. I will definitely use your site as my first, best choice for any problems I have in the future.

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

took out old agitator and installed new one, machine now runs like new. couldn't be happier.

The process to replace the nylon pieces was to remove the protective cap, (which snaps in place),agitator (which is held in place with a nut) you will need a socket with an extention to reach the nut, and worn parts. replace the agitator repair kit, agitator and protective cap and your washer works as good as new. This is a very simple repair job, even a 10 yr old could do this

I took out the softner dispencer and there is a bolt under tthe the plastic cover,I removed the bolt and the whole assembly came out,then I installed the new one and reinstlled the bolt and plastic cover,and reinserted the liquid softner dispencer.All only took about fifteen min.