7MMVWC220AW0 Maytag Washer - Instructions

My washer is an Amana He, but the part is made by Whirlpool, I think. I just set the new part on the middle agitator in the washer and pushed it firmly down and it snapped into place. It was amazingly EASY!!!!!!!

I simply watched the brief video supplied on both the page as well as my emailed receipt and performed the steps as directed. There were no deviations required... it was exactly how the video described it. Honestly, I expected a more lengthy and complicated repair!

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

Replaced agitator sprage kit. Simple instructions simple repair

Repair was extremely simple by using the video provided online. Works perfectly! Thanks so much.

The repair was exactly like the instruction vidio

I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3/8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.

I ordered these parts for next day delivery. The next morning they were on my door step!

I pulled off the plastic cover inside the agitator, under the softener dispenser and replaced the old "O" rign with the new one. Next I used a 3/8" socket with a 6" extension to loosen the agitator nut and removed it. The one on our machine was on rather tightly - a bit too tight in my estimation.

The upper part of the agitator lifted easily. I lifted out the cog mechanism and studied it. I took the new parts, and assembled them, using the old parts for visual reference. All of this took about ten minutes. Be sure you push firmly on the retainer until it locks in place to keep the cogs in their slots.

Next I spent about 15 minutes cleaning up the agitator just because I like to put stuff back together in 'clean condition'.

Next I replaced the thrust bearing. The instruction specified a special grease to lubricate the thrust bearing - order this when you order the parts. The original one had no grease on it and was quite worn. I used food grade vaseline. You could probably also use silicone lube on this, the part is nylon.

After I cleaned the assembly and put in the new thrust bearing, I replaced the agitator. I had slight difficulty lining up two grooves on the cog holder for the guides in the main agitator mount but got them lined up on the third try - that took less than a minute. I put the new washer on the nut, inserted the nut and tightened it down - be careful not to over tighten, just make sure it is snugged down.

Over-all this is a fairly straight-forward repair job and is not difficult - anyone who can follow easy to read instructions and run a socket wrench can do this. I would only caution to make sure the new cogs are correctly oriented in their holder. Study how the original is assembled so you can duplicate it with the new parts. Just for the record, the nut is standard right hand thread - lefty loosey, righty tighty.

I think these parts are made to fail on purpose - if the machine gets over loaded and the agitator can't work it will chew up the cogs rather than break the agitator. Good thinking on some engineer's part!

I was lucky when I found Parts Select - I'll come here for my parts from now on!

I simply removed the bolt from the inside of the agitator and pull the whole the straight up. It came aloose pretty easily. I took the old clothes mover off and put the new one on. On the inside of the mover the dog ears and spacer easily comes out. I removed the spacer and replaced the dogs ears. I put everything back together the way it was when I took it apart. It works as good as it did when I first got it.

1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, which you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.

I removed the agitator top cap first. I reached inside and removed plastic cap. I then removed the 7/16 bolt inside the agitator and lifted it out of the machine. I put my foot on the bottom part of the agitator and pulled the top part off. I removed the plastic bushing in the bottom part and then removed the plastic bushing with the dog ears and the bolt. I used some appliance grease on the bushing on the bottom part and slid the top part of the agitator back in place and replaced the 7/16 bolt. It worked like a charm. My wife says I'm her hero. Thanks for making it so easy.

Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting noise. Reassemble. The drawing on this site is helpful.

Removed top agitator bolt lifted agitator out and replaced ring and geared dogs. replaced Agitator top swirl vanes. It would have been nice if the kit included agitator grease and a new bolt and washer.