7MMVWC420BW0 Maytag Washer - Instructions

Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.

I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.

I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and within 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.

First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again

I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder part, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!

Very easy repair. Popped off the top cap on the agitator with a flat head screwdriver. Then took a half inch drive socket set with the extender and removed the assembly where the cogs were housed. Inserted new cogs, put it all back together and the thing agitates like new. Simple. Saved huge dollars.

got the parts from parts select and got the machine repaired quickly
what a savings
repair man would have been over 100 dollars
the shipping was more than the parts but I saved greatly with no repairman
love your site and the great savings
i really loved my washing machine and hating to lose it
was so satisfied that I could save it after all these years
thanks

Could be done in place, but it's easier to pull the full agitator assembly out first, and work at a table. Remove the fabric softener dispenser, then the plastic cap below (with rubber o-ring)- both pull out by hand. Reverse the now visible bolt with an extended 7/16" socket and pull the cog housing up and out, gripping with gentle pressure with pliers ( locking plastic tabs make this piece impossible to remove by hand). Once the housing is removed it's easy to separate the two halves with your fingernails and replace the cogs. I was able to reassemble everything and push it back down into the drum in about two minutes. Piece of cake- I highly recommend anyone with a tool box do this himself.

With the help of a You Tube video, which was watched first, then when the parts were delivered, the video was watched again, then we played the video back and paused it after each section was done so we could make sure we were doing the repair correct. The one thing I will mention that the video doesn't mention to do is, before taking the agitator out of the washer, put a mark somewhere on the agitator to tell you which end is the top. Just remember that the top( cap ) will be off, so that will not work. Otherwise it was a good, easy fix

First I popped off the very top cap of the agitator. I then used a socket extension to access the mounting bolt in the interior of the agitator. Once the bolt was loose i pulled the agitator off and dropped out the middle piece. With this out i switched the 4 cogs with the old. I then held the agitator assembly upside down and placed the middle piece back in. The most difficult part was aligning the agitator back onto the bottom part. Screw it back in place and pop the top back on.

To replace the dogs that cause the ratcheting motion:

I removed the softener cup by pulling straight up. (You've probably found, as I have, that the softener cup and the bleach dispensers are problematic: the softener cup must be cleaned with every use or the old softener liquid turns to glue, and the bleach dispenser mechanism plugs and distributes bleach onto your next load, ruining entire loads of clothes.)

Then I lifted the cap covering the retaining bolt by inserting a screwdriver alongside in the square holes provided, loosening it, and lifting it out.

Then I used a socket and a very long extension to remove the retaining bolt. I lifted the agitator straight up.

The next step can be a problem: I survived it (though I did strain my back). What's required, as you can see by reading the preceding letters, is to lift sharply on the upper agitator while holding the lower agitator with your bare feet or some soft shoes. What this does, at least on my model, is to break off the tabs that are fused together over the ratcheting-dogs, which are the focus of the repair. (These tabs hold the upper and lower assemblies together, moving the dogs assembly with the lower agitator.) In my case, one of the tabs broke off a half inch below the top, but that wasn't catastrophic and I didn't lose the rest of them, so when I reassembled the two halves still snapped back together.

One problem was that when I jerked the two assemblies apart, the parts of the dogs assembly went flying. Everyone had said to make sure everything went back the same way it came apart--for me there was no way to tell what that way was, but common sense tells you which way to reinstall the new dogs; they have to catch every stroke.

To reassemble, position the dogs with the retainer cup inverted. Then hold them upside down while sliding the upper agitator down over them. This holds them in place. When sliding the upper agitator down onto the lower, make sure the slots line up and use a smooth even pressure. Snap the two halves together, bolt the agitator back into the machine, replace the cap with the large o-ring (make sure you clean and/or replace the o-ing), and reinstall the softener cup.

Et, voila! You're back in business.

basically pop off the top spindle cover, reach in and pull off the water cap from the agitator cog cover, unscrew the bolt holding the cog holder and pull the agittator assembly up and off the machine. Remove the piece holding the gogs in place and replace cogs making sure to put them back in the same direction as they came out. Turn the agitator upside down and stick the piece holding the cogs in and snap it in. Replace all components in reverse order they were removed, and there you are. Works great.

Washer stopped agitating. I removed the clothes softener cup on top of the agitator by grasping and pulling up, inside the agitator I removed the inner plastic cap by grasping the 2 finger tabs and pulling up. There was a plastic retainer assembly with spring instead of the 7/16 nut referred to in other posts. I used a long 1/2" ratchet extension to remove the plastic retainer assembly, removed the top half of the agitator and replaced the cogs, then replaced the agitator, plastic retainer assembly with spring, snapped the plastic cap back on, and replace the clothes softener cup.

Snap off softener dispenser. Pop off top of agitator with flat head screw driver. Use long handled socket ro remove agitator fastener. Lift off entire agitator assembly. Flip upside down on floor. Secure top section of agitator between feet and carefully unsnap but lifting upper portion. Look at placement of existing agitator cogs in upper section between feet. Remove cog retainer. Note position of cogs. Replace one cog at a time making sure they are repositioned the same way. Attach cog retainer. Place bottom portion of agitator in alignment and snap. Flip over and reinstall on washer center assembly. Place bolt and washer back into assembly and retighten. reattach cover and softener dispenser (if you have one). Done! Less than 15 minutes.

popped off the softener dispenser, pulled out seal over nut assembly, used socket wrench with extention to loosen and remove nut holding cog assembly.
slid holding ring off of the bottom (mine was black in color) pulled out old dog agitators put in new ones, reverse assembled the unit tightened it down, (be sure not to go too tight there is a rubber bushing under the nut) ran a small test load of laundry and it now works great!!!!