7MMVWC420BW0 Maytag Washer - Instructions

Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.

I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.

I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the agitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!

Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....

1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!

This also gave me a chance to clean the agitator thoroughly!

The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.

I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and within 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.

FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.

I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.

Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.

I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the repair man.

first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.

Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..

THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE

We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.