MAH14PNBEW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from Oak Ridge, TN
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
washer smelled hot on spin cycle
Replaced the belt and motor isolators. Watching your video made it very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Rochester, NY
- Parts Used:
- WP22003329
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Appliance repair company did a poor job and the motor fell off because of a missing isolator
I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Phoenix, AZ
- Parts Used:
- WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Syphon cup had crack in it and had to be replaced
Syphon Cup is made one way and just slides into place...very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Scotts Valley, CA
- Parts Used:
- WP22004477
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Increasing water leak
The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from lafayette, CO
- Parts Used:
- WP22002119
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Whenever the timer hit the rinse cycle, my breaker would trip
First I took off the door and the front of the washing machine. Then, took off the bracket of the soap dispensing bin from the top of the machine. Then lift up the top of the machine, and unscrew the bracket that holds the wax motots, label and pull wires, replace motors and wires and put back together. This is also a good time to clean and dust the interior of the machine. Before replacing, my motor smelled and looked burnt out, instead of paying $300 -$400 to have someone look at it, I investigated and I fixed it for around $30. I hope I get to inspire people to figure things out and save some cash!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Sudbury, MA
- Parts Used:
- WP33001787, WP33001764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Door hinge hole covers broken
Unscrewed old screws, removed old plastic pieces, and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Orem, UT
- Parts Used:
- 22003083
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water leak through door
I read the reviews from others fixing this same part, it didn't seem to difficult. It was not even hard at all. I installed the part and my washer does not leak at all. My Neptunes are old so I am very sure I will come back to buy parts here. I did install the hinges backwards at first, the didnt close so I had to take an extra five minutes to turn them around.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Davis from Sacramento, CA
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
door boot seal broke
I am happy when PartSelect included the instruction video, so I completed my repair that easy. Thanks the PartSelect. Davis Dao
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from El Cerrito, CA
- Parts Used:
- WP22002119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Would not go into spin mode
Removed 4 screws and door, lowered and removed front panel,removed screws holding locking tabs for the machine top, removed the four screws holding soap reservoir, lifted the top. Located under the lid and above the doorway I pulled out the wax motor retaineing clip with pliers and the wax motor, used pliers to remove the wire connectors, hooked them up to the new part and reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from El Paso, TX
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Rubber Boot between Tub and Door had a hole
When I looked up the part number, there was an installation video on the same page. I ordered the part then and there, and once it arrived, I put the iPad right on top of the machine and paused the video whenever I was doing the steps. It was TOO EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauraine from Kimberling City, MO
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Started smelling rubber burning during spin cycle
I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Slinger, WI
- Parts Used:
- WP22003262
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
We had a leak in the tub pump hose
It was very easy...we ordered the part and it only took a day and a half and it was here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Mayville, MI
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water leaking in the front of the machine
My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sewickley, PA
- Parts Used:
- 12002533
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water leaking from the rubber front door seal.
I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Parma, OH
- Parts Used:
- WP22003262
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leak in tub to pump hose
removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.
Was this instruction helpful to you?
Thank you for voting!