MAV6200AWW Maytag Washer - Instructions

Took a screwdriver and pried up the top of washer, then reached in and unscrewed the front two screws that allowed the front to be lifted off.
Removed two screws on lower right side that allowed us to pry open right side of washer. There are six springs along the bottom of washer that keep the tub stable and keep it from bouncing against sides while in spin mode. One of the springs broke and needed to be replaced. Off course it was the one that was in the far back and the hardest to get too. But by prying open the right side it was reachable. The wife pushed against the tub to make the spring stretch a little less but still was too difficult. We took the advice of another home repair guy and put quarters in the spring (about $1.75 worth) to make it stretch out, then it was simple to connect the two ends, remove the quarters and voila....it was done. Screwed theright side back on, but the minimum order on the springs was six and the others seemed fine, we just put the other five inside the washer cabinet, replaced the front panel, reset the clamps on top of the front panel, slammed the top down and we were back in business. The parts including shipping was a little over $10.00. So I am sure we saved at least $140 repair job.

first we looked at schematics on your web site to see what we thought was wrong and if we felt we could do ourselves. It appeared to be seals and gaskets, so we went for it and carefully took the washer apart. We ordered the parts, cleaned the parts we had such as the tub, and were all ready to put back together when the parts arrived. Again, using your pictures, we reasselbled and when we tested, it worked better than it had been in a long time. And we saved a large repair bill!

Removed the front panel, Removed the belt from pump in the back of machine. Removed the pump from the back of machine, Put the pump in reconnected the belt, Replaced all the screws. My husband did the repair work in a matter of 45 minutes. Machine works fine now. The part came when I was told it would. I am very pleased with your service.

Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.

For safety I Unplugged the machine
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my

After pulling the machine away from the wall and turning off the water and unpluging. I simply removed the panel in the back and reached underneath and removed the belt. Took off the hose clamps and removed the three screws holding the pump on. Put the new pump back in place and hooked up the hoses. Then put the belt on for a test run.......all OK put the back on and was done. Whole job about twenty minutes. Saved over two hundred dollars doing this myself. Very simple repair.

i did the repair by the instructions that you had on the web site,and i thank you for all the help you gave me.

tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!

Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

First I took the front shield off, then I took the motor off.

just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

Very simple, Lid cam part was broken, Just need to remove broken plastic lid cam with screwdriver and then snap in place the new piece. Worked like a charm first time. Easy , inexpensive repair to a reliable washing machine. Bill

Removed old agitator, and installed new one. Very easy.

Needed a medium extension and a rachet a screw driver and a 13mm socket. I used a short screw driver and inserted in it the softer container and lifted it strait up to get the softner container out of the way. I used the medium extension to reach in the auger and loosen the small bolt holding the auger on the machine. Pulled it up and out. Reversed the above procedure and it was set to go. Total time about 8 to 10 minutes. Thank for all the help Kudos to all including Susan W.