MTW6700TQ1 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sheree from Clarkston, MI
- Parts Used:
- W10820048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Whirlpool Cabrio top load washer Error UL
Lived about 6 months with noisy, unbalanced, vibrating top-load washer that would not fully drain clothes or finish a spin cycle.
Watched as many You-Tube repairs videos as we could. Had difficulty trying to open the top panel for access to spin tub.
Discovered that we had clips in front, about 6" from each side, that needed pressure push with flat metal paint scraper, in order to open the top for access.
Other than that delay, took us about 2 hours total with two of us working together. In the end, Suspension Kit was exactly what we needed, and NO longer get the UL error code, with bothersome constant spin stops, which failed to spin water out of wet clothing.
Watched as many You-Tube repairs videos as we could. Had difficulty trying to open the top panel for access to spin tub.
Discovered that we had clips in front, about 6" from each side, that needed pressure push with flat metal paint scraper, in order to open the top for access.
Other than that delay, took us about 2 hours total with two of us working together. In the end, Suspension Kit was exactly what we needed, and NO longer get the UL error code, with bothersome constant spin stops, which failed to spin water out of wet clothing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Javier from SAUCIER, MS
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer would go into an unbalanced error code
Replaced 4 suspension rods. Had to release washer top from body case by twisting putty knife between lid and body. Once released swung lid up and propped against wall to access suspension rods. Replaced all rods and reinstalled lid. Good test run, no unbalanced error.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akemi from ORLANDO, FL
- Parts Used:
- W10820048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Hard to open the washer top
Watched an instructional video many times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PUYALLUP, WA
- Parts Used:
- WPW10619844
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid lock lite would not activate.
The most difficult was to lift the top up. Releasing the clips was tough to push in and it broke some porcelain. The 3 screws on the plastic instrument cover was all that was required. Track the wires and remove the plug in and pull the wires through the access hole and misc clips, a Phillips screw driver removes the plastic switch .Simply place the new switch under the lid and the worst is done. Once the lid was up, 10 minutes and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FLINT, MI
- Parts Used:
- W10820048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Rotted away do to a leak
Had to fabricate a new top holder for rod and bottom was still working. So far working great Thank God , because they don’t make them like this anymore!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from DUBOIS, WY
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water would not drain from tub.
Used shop vac to remove as much water as possible. Turned washing machine on side to access pump. Removed old pump. Installed new pump. Used nutdriver to attach three fasteners and pliers to attach clamps to hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corey from RUSSELLVILLE, AR
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water would not drain.
Follow the video instructions.
No brainer..
No brainer..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from KATY, TX
- Parts Used:
- WP8565314
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
dryer suddenly stopped heating
removed back panel, checked resistance across the thermal fuse. found no continuity, ordered fuse from Parts Select and it arrived in 3 days. removed one 1/4" hex cap screw holding fuse in place, removed 2 electric connections noting position. installed new fuse. this took a total of 10 minutes, excluding wait time for the part.
Please note, the cause of the thermal fuse melting was 10+ years of lint build up in the exhaust manifold. There is no point in replacing the fuse without addressing the cause, while we clean the lint filter regularly, the lint buildup in the manifold was appalling and glad the fuse worked. Removing the manifold and cleaning it out took another hour, but worth the time and effort.
Please note, the cause of the thermal fuse melting was 10+ years of lint build up in the exhaust manifold. There is no point in replacing the fuse without addressing the cause, while we clean the lint filter regularly, the lint buildup in the manifold was appalling and glad the fuse worked. Removing the manifold and cleaning it out took another hour, but worth the time and effort.
Was this instruction helpful to you?
Thank you for voting!
A rat ate holes in several rubber elbows in our washer
I got the three rubber elbows to quickly (at an additional price). They were the correct part and fit exactly. I replaced the aggravating spring clamps with new radiator-type screw clamps which made the job easier and in my opinion better. Then I devised a little hardware cloth "fence" around the bottom to the washer to keep the rat out. The job is tough enough in that you must tip the washer forward to get at the lower elbows. Also probably a good idea to adjust the feet "in" as far as possible to minimize rodent access from the bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORWOOD, NY
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Very noisy, compared to the original drain pump.
1st watch a video on replacement of this pump.
My main issue was the guard I had to install and the correct way to
put it in. I know I got it right.
The pump is very noisy, loud!
It pumps out just fine.
Want to know if this is normal, Loud pump.
Let me know.
Thanks, Dave
My main issue was the guard I had to install and the correct way to
put it in. I know I got it right.
The pump is very noisy, loud!
It pumps out just fine.
Want to know if this is normal, Loud pump.
Let me know.
Thanks, Dave
Was this instruction helpful to you?
Thank you for voting!
the drain pump leaked water
fairly simple remove and put back in …I watched a video of a similar Maytag pump replace got some tips…the electoral connection is shielded by a pull up tab…so it was quite simple I got extra hose clamps in case?…didn’t need them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from OCOEE, FL
- Parts Used:
- WPW10189966
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
F1 code show
Removed/ Replaced. Machine control motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MAGNOLIA, MS
- Parts Used:
- W10536347
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
Water pump was busted.
Just pulled the old water pump off and replaced with new one and was good to go. Thank you so much for sharing the problems and how to fix. Dean
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor m from campo, CA
- Parts Used:
- WPW10178988
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
mins after start it stopped and got code f51. then put it manual spin and got UL code
followed repair manual for code f51.ordered/replaced Rotor Position Sensor {RPS} disconnected and reconnected wiring harness at computer module and then put everything back together and that took care of the problem, It;s been working good since. that sensor was delivered the very next day. that was great. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Hamersville, OH
- Parts Used:
- W10820048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
replace suspension rods
lifted top using putty knife to push back holding clips.secured top so it did not fall. moved basket to one corner and lifted the spring up, while it was lifted remove the plastic holding rings. Then push down on holding clips that are near bottom of side of basket and the suspension rod just eases out. do that for all 4 and you are done.
Was this instruction helpful to you?
Thank you for voting!