MAT12CSEGW Maytag Washer - Instructions

Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.

Disconnected the hoses , power cord, and the drain hose. Tipped the washer on it's front panel and removed the old belt and spun the new one on. Tested for tightness as per the instructions and sat the washer up and hooked everything up. Total time---5-10 minutes.
Local appliance dealer insisted this wasn't the belt we needed. Thanks to your website we easily selected the right one. Thanks.

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

watch the video and it was very simple replace belts like they show on the video. lay the washer on it back and the belts was visabile. removed the small belt and then removed large belt, and replace the large belt and small belt. i used no tools. that because i lay the machine on it back.

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

I replaced the 3 screws because they were rusty. Then I replaced the Drain pump

Install belts.

Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.

Based on info from website, sounded like it was the Belt Kit that needed replacing. While waiting for the Belt Kit, decided to take the Agitator out to have a "look-see". OMG! There was liquid fabric softener gunk so thick in, around, underneath the agitator that the unit could not get traction. The burning smell was the gunk getting hot as the agitator tried to work. After a thorough cleaning of the agitator and anything relating to it's ability to agitate, my Maytag is performing like it was brand new! I'm keeping the Belt Kit, because my washer is older and I've heard from friends and family that have purchased the new water restricted units, absolutely hate them; like the "low flow" toilets, instead of flushing once, you now have to flush 5 times. They are washing more smaller loads and double rinsing each load to get their clothes clean and free of residue. I'm a 69 year old woman who finds your website and your marvelous contributors an absolute Blessing!

Removed wet close and removed 99% of all the water with a simple sifon hose and sponges. Diconnected electric and water supply hoses. Layed washer on its back. Removed front of washer. Disconnected hoses to water pump and checked for blockage. None. You need to capture the risidual water from the hoses and the pump if you are working in an area that cannot tolerate spills. Pulled pump out (three screws) put a screwdriver and blocked the pump impellar and rotate the punps pully. Pully rotaded freely so the pump is bad. The two belts were pretty worn out so I replaced them also. Hooked up everything in reverse. Adjusted the tension of the belts as required. The drive belt for the pump should be pinched to 1/4". Checked the moter glides also. Put everything back together, checked for leaks and did a load of wash. Everything good. Dismanteling and diagnostics and clean up took about 30'. Assembly took another 30'. Purts fit perfectly.

Removed 2 Philip screws from bottom front panel. The belts came as a set, so pay attention to the belt sizes when replacing them. Have had the new belts installed now for a week or longer with no issues. Looks like a good fix.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00

Chalked the transmission with a pipe wrench. Removed the brake with grabbing on to it with vicegrips and hammered on the vicegrips to remove the brake. The new brake spun on after the first two brakes didn't. Working great now!

Followed the first guys directions.
remove front
lift top
remove agitator
remove locking nut clockwise
remove inner tub
remove Mounting S loosen set screw and clockwise also
clean well
replace boot as shown in tip in sheet
push boot on completely

Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.