SAV365ZAWW Maytag Washer - Instructions

Unplug the washing machine. Removed the three screws that held the control panel on the top of the washer. The panel then rotated forward exposing the timer control. Remove the knob cap, timer knob, and one screw that secured the timer. Remove the timer from the panel, unplug the wiring harness connector. Reverse the process to install the new timer. Fixed problem completely.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!

Removed upper back panel.(3 screws) Unplugged washer and remove timer. Unplug timer from wires. Replaced timer and reinstalled.

Removed broken piece and put on new part.

I disconnected the water supply line to washer and moved washer into open area. I removed the front panel of washer to gain access to drain hose. I removed hose and reinstalled new hose. I did turn the hose holder inside the washer as it allowed the old hose to rub against the housing support of the washer causing the hose to leak. I was glad that I read the article that someone mentioned in their repair. The new hose was somewhat difficult to maneuver through the back of the washer and through the part that held the hose; otherwise, it was rather easy. Thanks for the feed back on your web page.

Ipulled the front panel off and found that the brake pads had broken into pieces, ordered new pads. Two of the pads were accessed from the front of the machine and were relatively easy to replace by removing the two attaching bolts, spreading gap in area that they fit into with a plastic pry tool. I gained access to the third pad by removing the punch-outs on the side of the machine (circular). If I had not had these prepuched pieces available to me I would have simply cut an access hole in the rear of the machine with a jig saw, (who will ever see it).

First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.

Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim

MAYTAG SAV2655AWW Series 10 Washer Tub Bearing and Seal Replacement

1. Unplug washer power cord and turn off water supply to hoses.

2. Remove lower front panel, 2 5/16” hex head screws at bottom of panel.

3. Remove front upper panel, 2 5/16” hex head screws at bottom corners of panel.
4. Slide washer out from wall far enough to provide clearance to lift washer top panel and control head.

5. Remove 2 5/16” hex head screws securing washer lid panel to side panels and lift lid.

6. Pull fabric softener dispenser from agitator, pulls off easily.

7.Remove agitator upper section, pulls off easily. Remove ½” hex head retainer bolt from inside agitator.

8.Remove agitator base section, pops up, place fingers under each side and pull up gently.

9. Remove tub top ring by pushing down at each clip and then prying out lightly to disengage clip, 8 total. Orientation for reassembly is done by referencing the double tabbed clip on the right side of the outer tub.

10. Remove inner tub retainer bolts, 4, ½” hex head. Clean off mounting hub to expose 4 pry slots located exactly opposite each other. Using wide flat head screw driver carefully and evenly pry up inner tub off of aluminum mounting hub. Once tub is ¼” or more raised a wider blade pry bar will help prevent cracking or breaking the inner tub.

11. Remove plastic seal cup from transmission shaft by turning it counter clockwise with a medium to large pair of water pump pliers.

12. Remove inner tub aluminum mounting hub by using a hammer and broad flat faced punch or drift and driving the hub counterclockwise. You can be aggressive about this as kit comes with a new hub. It will loosen at some point and can be unscrewed by hand. The transmission shaft threaded section must be thoroughly cleaned to remove all sealers or debris from the threads or the new hub in the kit will not thread on correctly and will be excessively tight. Lightly place anti-seize lubricant on the threads before putting on new hub and seal cup.

13. Remove water pump hose from outer tub. Then remove second hose from water pump.

14. Remove “Fill Sensor” hose. Back left quadrant of outer tub, pulls off easily.

15. Remove 6 tub ( 3 pairs) stabilizer springs, plus 1 spring in very back. Try to watch how back one connects to tub mount. If you miss it hooking it back up is pretty straight forward. Only secures one way. Channel locks or vise grips work best for working with springs.

16. Disconnect wire harness from motor drive assembly and tub frame mount.

17. Pull tub and motor drive assembly out of washer cabinet. Lift carefully by shaft and tub mount frame.

18. Remove 6 outer tub retainer bolts and 2 upper motor frame bolts.

19. Lift tub off motor frame and set on its side carefully to prevent damage to “Fill Sensor” back left side.Use a slide tool to pop bearing assembly out of tub bottom.

20. Clean the tub, bearing mount surface, remove all grease from shaft and shaft spline sealing O-ring.

21. Wet new bearing seating surface and tub mounting surface lightly with water and press in new bearing by hand.

22. Clean both inner and outer tubs inside and out thoroughly. Clean hub mounting threads on motor shaft thoroughly.
There can be no residue of any kind in those threads or new hub will be difficult to impossible to screw on without damaging it.

23. Reverse dis-assembly procedure to reassemble machine. Recommend replacing drive belt and idler pulley if found to be excessively worn or damaged. If brake assembly is heavily worn or pads are cracked this is the time to replace those as well.

took the belt out and took the thing out and fixed then put it back.

1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump

Pushed new knob onto shaft