MAH21PNDGW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gordon from ALAMEDA, CA
- Parts Used:
- WP22002941
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Broken dispenser lid
Received the new lid but the pins required to install it were not included. The old pins were corroded and broken. Used a couple of nails of the correct diameter and cut them to length with wire cutters. After that, I just pushed them in to place, job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd & Shirley from CHADRON, NE
- Parts Used:
- W10181639
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
washer was noisy so I replaced the bearings and put a new shaft on the tub
I looked on Utube at some videos which helped a lot all told i replaced the bearings in the outer hub which was quite a chore as the bearings came out rather hard I used a steel rod about 18 inches long and a heavy hammer to pound the old bearings out they came out hard then I put the new bearings in very carefully as I had to tap them back into place and installed the seal and put the new shaft on the tub and slid everything back into place. The instructions that came with the new seal and shaft were very helpful I bought the new bearings from local implement dealer as they were not available with the shaft and seal didn't keep track of my hours probably about 21/2 to 3 hours
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Warwick, RI
- Parts Used:
- WP22002798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door hinge worn.
Very easy.I used a screw driver to remove and install the new hinges. Three screws on each hinge. Door closes like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Bonham, TX
- Parts Used:
- 33002973
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
replaced two baffles
took off the dryer by remving two screws, then the front panel. Then removed the screws that held in the drum, pulled the drum out replaced the baffles then put it back together. It was easyer then I thought. It took less them 30 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Ringle, WI
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking front door~cause: hamper wires wriping inner plastic door liner
Removed door, changed over parts from one panel to the other, then rehung door....extremely easy! Thanks for the part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Stanton, IA
- Parts Used:
- 22002266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased a front load washer, missing siphon cap
Ordered siphon cap according to FPS parts list. Wrong cap, but I don't care! Customer support was so helpful and willing to do everything to get me the correct cap, to include refunding my purchase price AND shipping before I even sent it back. They will be my first choice for parts in the future! My husband is a "fix it" guy, so I know that will mean a lot of purchases. I look forward to future business with this company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sudie from Ocala, FL
- Parts Used:
- 22002266, WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing parts
Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from amston, CT
- Parts Used:
- WP22003262
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
leaking water
removed one panel and front door to access under tub.leak solved!!!! thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jupiter, FL
- Parts Used:
- 12001413
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Deteriorated and clogged strainer; slow water fill.
Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Westminster, CO
- Parts Used:
- 22002266, WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing these parts
Bought the parts and just inserted them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Donald, OR
- Parts Used:
- WP22002798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door sagging
The service representative knew exactly what was needed from the description of the problem that was given to her. The hinges were received within a few days. The door was removed and the hinges were replaced and it does not sag anymore. Thank you for your great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Slinger, WI
- Parts Used:
- WP22003262
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
We had a leak in the tub pump hose
It was very easy...we ordered the part and it only took a day and a half and it was here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Rochester, NY
- Parts Used:
- WP22003329
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Appliance repair company did a poor job and the motor fell off because of a missing isolator
I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Scotts Valley, CA
- Parts Used:
- WP22004477
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Increasing water leak
The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Phoenix, AZ
- Parts Used:
- WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Syphon cup had crack in it and had to be replaced
Syphon Cup is made one way and just slides into place...very easy
Was this instruction helpful to you?
Thank you for voting!