MAT14CSBGW0 Maytag Washer - Instructions

replaced handle

As per partsselect.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

After seeing video it was easy . Took everything apart tub,basket,replaced all springs. Tub wear pads. It took longer because I cleaned eveything,took my time. There was a lot of deposits on tub and outer tub also some rust . Put it all back together all nice and clean . pluged it in put it in spin cycle and the motor just hummed. I than check to see if somethig was stuck no .Pulled motor tested it with out a load and did not work. Motor start winding went. Motor died. 2n one in 7 years. So I fixed that proplem I am a new owner of a Speed Queen washer and dryer .

It was actually much easier than I expected. The worst part was dealing with the gear oil as I drained it to clean out the plastic pieces that came off the gear. To see how to fix things like this, I went to Google, enter my model and what the problem was and watched a repairman do it. It seemed easy and it was.

Very old washing machine began to make a horrible noise and agitator would attempt to agitate during spin cycle. Eventually determined that the problem was in the transmission. The way the transmission works is that when the motor runs in one direction a metal fork pushes on a cam mechanism and lifts a spring loaded gear on the agitator shaft from the gears that make it move, putting it in neutral so that it can spin freely with the basket in the spin cycle. When the motor runs the other way the same fork pulls on the cam and drops the gear down so that it engages with the agitator mechanism. The problem was that the plastic cam pieces on the base of the shaft had worn down to the point where they where not fully lifting the gear clear and it was partially engaging with the drive mechanism. Repair was relatively straight forward except the YouTube video that I was using showed the parts on upside down. All the other transmission parts are labeled with TOP on one side but oddly the cam pieces are not marked. For reference the U shaped protrusion on the cam parts goes on the top of the assembly, not the bottom. All in all it took me about 12 hours to do this fix, but at least 10 of that was simply trying to figure out how the mechanism worked and tracking down the problem. Be sure to refill the transmission case and use some RTV sealant to seal the cover back on when you are done, just like you would for an oil pan on an engine.

Parts Select is outstanding..They diagnosed the problem quickly..The part was sent within 2 days and we were washing laundry the 3rd afternoon...THANKS!!!!!!

Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.

The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

Replaced broken and worn wear pads per online instruction.also replace tub springs and counterweight spring.all very simple.

We search on line the possible cause for our problem and Partselect offered the possible cause and solution. We watched the video on replacing the water pump.We then ordered the pump and 2 hoses.We followed the instructions and after removing the front panel, we found out one of the pump retainer was rusted away. We tried to look for local supplier and was shock that Sears was charging 20 bucks for a single retainer, which Partselect only charge dollar and eight cents. We ordered the 2 retainers on Thursday and it arrived on Saturday afternoon. We were able to fix the problem and are very happy there was no more leak. I wish the retainers come with the pump even if you include the extra cost to the pump pricing. We could have save the extra shipping charge for ordering the retainers only. I would definitely order more parts from Partselect and recommend it to my friends. Thanks again for your help.

Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

Since I had taken the washer apart before to find the problem, it was easier to remove the cabinet.Four screws and a electic connection. I remove the cabinet to get to the balance ring.I removed the tub ring by releaseing the catches and pried off the ring. Installation was just the reverse. Had some trouble putting the cabinet back whereit needs to be but once I got it the rest of the job was easy.

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.

The prooblem started with the hole in the bottom frame, for tub spring wore through, spring fell off, then a spring retainer worn broke in 2 releasing 1 suspention spring. All springs were about to fail, metal very thin at at the contact points. Drilled a new hole for the new suspension spring, replace all 3 brackets, worn also, springs, and retainers with a small dab of grease at the contact points. The new springs mad the tub more stable than before the failure, and silent when spinning or washing. Be careful to get the springs in the right direction, then the spring comes over the outside the brackets and retainers, other way they rub in spots. On this machine one was backwards from the factory 18 years ago, surely that accounts for more stable running.