MAT14PDAGW0 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ellen from NYACK, NY
- Parts Used:
- WPW10119828, WP21097
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
machine wouldn't turn on when lid closed
replaced missing screw and pad and now machine works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GONZALO from HAINES CITY, FL
- Parts Used:
- WPW10187167
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Timer opened water valve and activated agitator at the same time.
Diagnostic: damaged timer
I unplugged and opened the control panel to remove the timer. Once removed, I installed the new timer. I placed the control panel back, plugged back, set the timer, and go! It's working like a brand new washer!
I unplugged and opened the control panel to remove the timer. Once removed, I installed the new timer. I placed the control panel back, plugged back, set the timer, and go! It's working like a brand new washer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from DELANO, MN
- Parts Used:
- 350849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Agitator not working properly
I made the mistake of ordering the parts without watching the video. I got everything I needed on my order except the special grease that was required, so I had to delay the completion of the repair and pay shipping again to get the grease -- this was my error. The repair was easy and didn't take too long, the video was right on, the parts fit exactly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from BRONX, NY
- Parts Used:
- WPW10086010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
washer not spinning
First time .Replace the clutch .miss placed one of the retainer clip .found it after the replacement came .It was in the fold at the base of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindie from DUNMORE, PA
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable), Wrench set
Front legs were rotted.
Replace front legs. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ROSWELL, NM
- Parts Used:
- WP8546127
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Pump requires 2 retainers. I had 1 good retainer on the top and little tension on the bottom.
Pull the washer out away from the wall and tip back.
I used a small metal ammo box to hold up the washer.
The bottom pump retainer is easy reach and remove with a flat screwdriver. I was able to pry off with my hand.
Replace retainer insert into slots on drive motor and twist.
I used a pair of Channellock pliers to lift retainer while pressing along the
side till it snaped into place.
Remove the support box and put washer back.
Then tip washer forward to reset self-leveling mechanism.
I used a small metal ammo box to hold up the washer.
The bottom pump retainer is easy reach and remove with a flat screwdriver. I was able to pry off with my hand.
Replace retainer insert into slots on drive motor and twist.
I used a pair of Channellock pliers to lift retainer while pressing along the
side till it snaped into place.
Remove the support box and put washer back.
Then tip washer forward to reset self-leveling mechanism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from ROCKY HILL, CT
- Parts Used:
- WP63907
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Washing Moving All The Time-Lefth-To Right All The Time.
Pulled it apart,layed it down and looked at it,and chaned the 3 springs. And it is like new again. . . . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Lennon, MI
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Sherwood, OR
- Parts Used:
- WP9872207S
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door handle scratch
replaced handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Markle, IN
- Parts Used:
- WP63907
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Tub out of balance on spin cycle. Very Noisy!
I the took washer to where I could lay it on its side.
Laying it on its side lets the suspension spring at the top go slack. Making pulling it from bracket easier.
Next , I lifted the tub up with a 2x4 and blocked it with another wood block. This let me have slack in the lower springs.
Of coarse I saved the hardest one (behind the motor) for last. I only swore a little! But got it to come out.
By the way, put in each new spring, before going on to the next one.
The new springs helped a lot, but I ended up ordering the wear pads a day or two later. They were very easy to replace. Just pop the old ones out of the frame with a screw driver. then pop the new ones back into the holes and you are done.
You may just want to buy them both and do it all at once. Saving moving the washer twice!
Laying it on its side lets the suspension spring at the top go slack. Making pulling it from bracket easier.
Next , I lifted the tub up with a 2x4 and blocked it with another wood block. This let me have slack in the lower springs.
Of coarse I saved the hardest one (behind the motor) for last. I only swore a little! But got it to come out.
By the way, put in each new spring, before going on to the next one.
The new springs helped a lot, but I ended up ordering the wear pads a day or two later. They were very easy to replace. Just pop the old ones out of the frame with a screw driver. then pop the new ones back into the holes and you are done.
You may just want to buy them both and do it all at once. Saving moving the washer twice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Forrest from Oxford, AL
- Parts Used:
- W10814296
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer leaking
After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRUCE from UNION, NJ
- Parts Used:
- WP8546127
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water leaking from bottom of washer.
We search on line the possible cause for our problem and Partselect offered the possible cause and solution. We watched the video on replacing the water pump.We then ordered the pump and 2 hoses.We followed the instructions and after removing the front panel, we found out one of the pump retainer was rusted away. We tried to look for local supplier and was shock that Sears was charging 20 bucks for a single retainer, which Partselect only charge dollar and eight cents. We ordered the 2 retainers on Thursday and it arrived on Saturday afternoon. We were able to fix the problem and are very happy there was no more leak. I wish the retainers come with the pump even if you include the extra cost to the pump pricing. We could have save the extra shipping charge for ordering the retainers only. I would definitely order more parts from Partselect and recommend it to my friends. Thanks again for your help.
Was this instruction helpful to you?
Thank you for voting!
When the machine was filling with water about 30% of it would miss the tub and run down the back of the machine and on to the floor.
After removing the front, sides and top of the machine (all one piece) the springs were relativley easy to access. I discover one of the brakets that held one of the springs had rusted and would no longer support the spring. I then replaced the bracket and springs. I Re-assyembled the machine and it work as good as new.
Was this instruction helpful to you?
Thank you for voting!