MAT10CSEGL Maytag Washer - Instructions

It would seem that my unhappy washer decided to
have a multiple component breakdown. after replacing one part after another, my baby runs like new. parts arrived quickly and installed easily, it was all the diagnostic that took the most time. the forums were quite helpful.

A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

Replaced the air tube, existing one had been chewed by mice was easy to replace and solved the issue

after checking obvious reasons (plugged in, breakers,) i took off control panel cover and saw that the fuse was blown, replaced it, plugged back in and it worked. After 1st wash was done, again it didnt work and the fuse was blown. I followed the wires from the fuse and they led to the lid check switch,which had a char mark leading me to beleive it was fried. I checked for continuity with an ohm meter(after disconnecting the power of course) and got no reading after pushing in the red button on the switch.I googled maytag replacement part and Partselect came up.Easy to understand ordering, and $20(including shipping,2 days later and about a half hour install, my machine was running

Done a troubleshooting problem online. Figured out the problem and ordered the part. Removed old part installed new part and I am a female not that it should make a difference but some would say it does. Had the old part out and new part put in and it took me about 30 minutes. Washer now works like a new machine. Very pleased and proud of myself. The part was the lid switch assembly.

Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.

Removed front of control panel on the washer. Found the lid check switch, removed one screw, leaving the wires attached and replaced the old switch with a new one. Removed the wires from the old switch and place them on the new one. Reconnected the machine to the outlet,,closed the lid and listen to it run.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

Disconnected the hoses , power cord, and the drain hose. Tipped the washer on it's front panel and removed the old belt and spun the new one on. Tested for tightness as per the instructions and sat the washer up and hooked everything up. Total time---5-10 minutes.
Local appliance dealer insisted this wasn't the belt we needed. Thanks to your website we easily selected the right one. Thanks.

Checked the fuse it was blown. So I replaced it, pluged the washer back in. pull the start knob that's when the lids switch sparked and blew the fuse again.
Found you on line ordered the complete assemble to save me from the trouble of slowly change each.
Switch out the wiring from old to the new assemble. Line it up, one screw and a little adjusting and the Maytag is back in business!
Thxs Guy for the quick shipment had it in two day on a ground shipment!

I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.

Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.

Remove the rear panel covering the control panel. Remove the two screws on each side of the upper control panel. The top removes with gentle (or not so gentle) taps toward the front of the washer. Lift the upper away but be careful of the attached wires. Top must be removed or switch cannot be removed as it cannot pass the cycle selector. Note the wire positions and colors to the switch assembly, remove them, and loosen the screw holding the switch assembly in place. Tilit assembly up like opening a book and lift up and away from the washer being careful of the lid switch actuator below. Replace with new assembly, making sure actuator is positioned to activate switches, and reattach the same screw. Reattach wires to appropriate places, replace top control panel and reattach screws, replace rear panel.

all went well until testing. tub level did not shut the water off, caused a spill

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.