MAT10CSEGL Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wayne from SEDONA, AZ
- Parts Used:
- 22003428
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Threads on old legs had been damaged in moving to new location.
Removed the damaged legs, replaced with parts from this site and leveled the washer .
Was this instruction helpful to you?
Thank you for voting!
Broken Belts
Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from Northport, AL
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Motor quit running.
Took a look at the new door switch assembly, used a socket wrench to remove the old, took wires off of old and attached them to the corresponding terminal on the new. attached the new assembly inside the top panel. Works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Manhattan, KS
- Parts Used:
- WP6-2022030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Water was leaking from under the front of the washer when it was used.
After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Los Angeles, CA
- Parts Used:
- WP22001682
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Blown switch
The hardest part was actually finding the right part. It was easy to take of the control panel. make sure you unplug and plug in the correct wires....
I thought that would be it, but after doing that you need to fine adjust the whole assembly so that the timers and automatic switches work well.
That's about it.
I thought that would be it, but after doing that you need to fine adjust the whole assembly so that the timers and automatic switches work well.
That's about it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EL from O'Fallon, IL
- Parts Used:
- WP211726
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Resin balls on which the top loader lid hinges had broken.
Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.
Was this instruction helpful to you?
Thank you for voting!
short in door lid switch
Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nicholas from white plains, NY
- Parts Used:
- 12112425
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
agitator did not move, all other functions OK
Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryl from Newton, NJ
- Parts Used:
- WP22001187, WP22001186, WP596669
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Upper and Lower Fill Injector snapped off and water was leaking out of the back of the machine
I looked at the machine diagram on the website and removed the screw on the bottom and lifted up the from panel which allowed me to have easier access to the fill injector. Then I removed the back panel off of the control panel on the top of the machine and removed the screw that held the fill injector in place, attached the new fill injector using the hose clamp I ordered with the part ( you need a new hose clamp because the other one is useless after you remove the old injector). Tightend up the screw to hold the injector in place and replaced the back panel and front panel. It was an easy repair and only cost $28.00 with shipping. I easily saved $150.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from york, PA
- Parts Used:
- W10820036
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer would not run
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this instruction helpful to you?
Thank you for voting!
No tub spin, burning smell.
Partselect.com gave me a very helpful list of parts per symptom. Said that there is an 88% chance that belts were my problem. Since the machine is 200 miles away I ordered two other parts as well. Belts fixed it! Took front cover off (not totally necessary). When the machine is tilted back belts are exposed underneath. Two belts later I was up and running. This site is really great.
Was this instruction helpful to you?
Thank you for voting!
broken belt
Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!
Was this instruction helpful to you?
Thank you for voting!
pump and drive belt was thorn
Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.
Was this instruction helpful to you?
Thank you for voting!
burning smell from washer
Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from ANKENY, IA
- Parts Used:
- 12112425
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
smelled like something smoking
took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you
Was this instruction helpful to you?
Thank you for voting!