MAV7557EWW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from MADISON, TN
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Loud noise in spinning cycle
There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Disney, OK
- Parts Used:
- WP21001598
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Washer banging and moving during spin cycle
I watched the installation video. It was very helpful to see it done before doing the repair. I followed the video to take the old springs out and installed the new ones. Remember to check the snubbed ring and replace it too. The new springs and sunnier ring solved the banging and moving during the spin cycle. Now the washer is like new and the repair was less then $100. Thanks parts select, the help was greatly appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from CONNEAUT, OH
- Parts Used:
- WP22003989
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Timer and timer knob were broken.
Watched video from on YouTube. Disasembled dryer by removing cap from timer knob. Pulling timer knob off the shaft. Removed three # 15 torx screws from the top of the dryer. Top panel rolled forward. Depressed plastic tab removed timer and unplugged wiring harness. Ordered parts from this site online. Parts arrived in 2 to 3 days. Parts were installed following reverse order from above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Exeter, NH
- Parts Used:
- WP21001598
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
weak suspension springs
Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DWane from Waterford, PA
- Parts Used:
- WP21001598, WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
noisy washer and shaking
disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brena from Seaside, CA
- Parts Used:
- WP35-6780
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Busted Pump
We had a repair guy come in and he said fixing the pump would cost at least 250. I called my dad and he walked me through it over the phone. I took off the back of the washer, and laid the washer on it's side. I then had to take a break as I had flooded my kitchen. (Lay the washer at an angle.) The belt was taken off by the repair guy. I then undid the hoses, taking the clips off with pliers. Next I screwed the new pump in, and put the hoses back on. FInally I took the belt and stretched over the two small pullies, and then pulled it to the bottom of the big pullie and started spinning it until it wrapped itself all the way around. It wouldn't have taken over an hour but I had a baby who needed me ever couple of minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELMORE, OH
- Parts Used:
- WP22004469, WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer Traveled and load would not be balanced. Washer would bang loudly.
Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from erie, PA
- Parts Used:
- WP22004385, WP35-2328, WP22003483
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Seal Leaked
1 I opened the top of the washer found the top plastic rim piece broken due to the fact that it cracked while unbalanced one time. Which made it leak which ate away the rubber seal . The parts were here fast and they were the right ones. Great job and I will tell everyone about you thank you verry much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Aplington, IA
- Parts Used:
- WP22003285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
water on the floor
figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.
Put clamps on new hose, replace hose and slide clamps to ends to seal the connections
Put clamps on new hose, replace hose and slide clamps to ends to seal the connections
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Evans, WV
- Parts Used:
- WP22003804, WP22002754
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid switch was broken when the lid slammed shut
The installation was extremely easy - videos sure helped. I would recommend this site for appliance parts - parts came ahead of schedule.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOUG from COLDWATER, MI
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
water pump froze during spin cycle
I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barney from TORRANCE, CA
- Parts Used:
- WP22004333
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking water into the tub
Watching the u tube video associated with the part made the repair even easier. I’m very handy but gave me a better idea of what to look for and tools needed for the repair ahead of time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from FREMONT, NE
- Parts Used:
- WP22003483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
spinning slowly
This was a very easy fix.....roll belt off....roll new belt on....seemed to help not sure if it fixed problem....might try pulley and bearing kit next
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- antony from ALTADENA, CA
- Parts Used:
- WP22002753, WP22002751, W10814230
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the wassher would shut down mid cycle. jamming a screwdriver in to force the lidback solved theproblem
I popped out the hinge pins, popped outthe busshings, popped out the cam. time less than 10 minutes, pressed in the limit cam, pressed in the bushings, pressed in the hinge pins. time about 5 minutes. the most important thing is my wife is extremely happy. I'm happy the parts fit perfectly.
also the parts arrived in 2 days.
also the parts arrived in 2 days.
Was this instruction helpful to you?
Thank you for voting!