PAV3855AAW Maytag Washer - Instructions

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

unscrewed screw holding old actuater in and replaced it whith the new part.

I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

Pull broken knob off, push new knob on.

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..

I removed the old pump put the new one in its place. In twenty minutes i was ready to was clothes. It was so quite i thought something was wrong. I received the part in three days the timing was great.

The repair was easy. I had to unscrew on bolt, place the agitator assemply on and screw the bolt back down. Simple , Sear was gonna charge 175.00 just to ship the part. I got the part for $57.00.

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

After taking the motor off (it looked loose to me!) and stripping out the bolts on it, then finding that the bolts holding the motor were permanently affixed to the motor (and they were an odd size not available at the hardware store), I drilled the bolts out and put in new ones (on the motor) and re-affixed the same. I still had a problem. I then went online and found that most people had problems with the water pump. I looked at the pulley on the water pump and found that the inner shims had slipped out on a permanent part (and could not be put back in with the basic tools I had on hand). I ordered the pump online, and replaced the same. Took about 30 minutes after I found the real problem and got the parts in. My pump had a permanent metal disc on the bottom which did not come with the new pump, but the new pump fit without it. Machine works fine now.

Removing and installing the pump is theoretically easy, as everyone on this site has said so far. Just remove three hex-shaped screws, loosen drive belt and remove pump, then install new one using the same steps in reverse order. The trick is getting the screws off and on--they do not have slots for a screwdriver and there is not room around them for a socket wrench or pliers. I probable spent over an hour just on removing/replacing these screws and have many bruises to show for it. I ended up attaching a vice grips on the tips of the screws underneath the washing machine and screwing them out that way. And replacing the drive belt was horrifically difficult--that's where the other hour went. The devil was definitely in the details! If anyone had told me what I would have to go through to make this repair, I would have called a repairman. And I am an extremely handy person--I do stuff like repairs all the time, so it is unusual for me to say this. The good news is that the new pump works and the washer is back in commission.

Took the whole machine apart tipped tub upside down to put on snubber ring. One person had to hold down very very firmly to the metal ring that fits on top of the snubber ring while another person quickly screwed in the screws to hold it down.
The springs required an extra strong person and a few words of frustration to stretch to get them on. My son who is 39 years old did it. My 60 year old husband would not have had the strength to stretch the springs.
So far it works great. My son washed his carheart jumpsuit and coat with not a sound or wiggle. Your trouble shooting site was what made us decide to order what we did because of the percentages of what the problem was beside each part. Thank you for being so prompt in sending our parts.They came so quickly we weren't without a washer but maybe a day or two.

Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.

used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.

Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from underneath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.