MAH21PDDGW Maytag Washer - Instructions

I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

I followed the video for the installation. I did find that installing the spring was no way as easy as it looked in the video. Otherwise, OK.

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

What transpired was removing the guts from the old inner door and putting them onto the new door which extended the time. Not sure about the tools because my handyman/friend did the installation while I was gone. He was a little frustrated with it. Otherwise, the door fit well. We decided that using hot water was the problem with the water leaking from the door. Using cold and warm water settings seems to make a difference.

Followed the PartsSelect video for the seal replacement, which was step by step and spot on, I just had to add the bearing replacement part myself. Once it was dissembled I drove each bearing out by tapping them with the hammer and drift. My model had no bearing retainer ring. I did not remove the outer drum from the washer. Clean the aluminum hub real well, scrape it with a utility knife to remove corrosion, wipe with a solvent soaked rag, etc. I disagree with other methods ive seen while researching, like a wire brush in a drill, because you will remove aluminum material from the hub and the bearing wont fit as tightly as designed. tap in the rear bearing til fully seated. I did the rear first because gravity then held the spacer in place. Set the spacer in place, noting that one end is "flared" to a larger diameter, so it seats against the larger race of the front bearing. Align and start the front bearing in place. The spacer needs to align with the bearings so it bears against the inner races of the bearings. So to hold it in place I rolled up a piece of light cardstock, slid it thru the spacer and bearing, and as it "uncoiled" it aligned the spacer. Pretty well. I did have to tap the spacer a little with the drift after the bearings were in, but just a little. After that, back to the video for the seal and reassembly. Only other comment I have is to locate the bearings early. I ended up going to grainger for one and Napa for the other. And no one could seem to cross the "DU" part of the original NGK bearing. The DU means it just has seals on both sides. Pretty standard stuff. That could have been easier. Also hold off ordering extra parts. I have found PartsSelect is really quick getting stuff out. I ordered an inner drum because i heard from other research that that could cause the banging noise. My banging noise was from one bearing disinegrating and the balls breaking up inside the hub. Shipping the drum back cost 70. UPS wanted 160. So that could have gone better, but I didn't want to let the machine sit too long. Next time I'll let it sit a couple days.

Removed tub replaced bearings. Put in new seal. Be aware drawing on instruction shows seal cup instaled from wrong side of seal. Other wise went well. Got bearings from McMaster Carr.

Being a seventy five year old man I was reluctant to taking on this job but after getting prices for the repair or replacing the machine I cringed and trying to save some money I took on this job.Got all the information I could find on line I got started.Taking machine apart was easy and remembering to keep parts separated is something I learned from my mechanical back round is a must.Pictures also help.Taking out spinner drum easy.Bearings a nightmare If you don't have a bearing removal tool.Front bearing had to be cut out with a dremel tool and zip wheel being careful not to destroy the race.Removed spindel from spinner drum as I could see that for me to put shaft in hole would have been a problem.Put new improved seal in.Easy part.Reassembled. Springs and clips hard.Washing again and quiet.Wife happy four days later.Old guy sore.All done with outer tub in machine.Estimated savings Big,Big,Big.Getting big steak dinner and big kiss.

Removed front panels, lifted top to open position, removed back cover, removed drive belt, drum pulley, removed rear bearing snap ring, removed seal clips, removed 3 baffels then the 3 mount bolts. Pulled out spinner support and the inner drum. Removed the rear bearing #6206LL with brass drift rod and heavy hammer (came out with little effort. The front bearing #6207LL I soaked with penatrating oil overnight (this bearing was making all the noise as after 11 years water finally got to it) The next morning I had little trouble removing it with the brass rod and hammer, taking my time to work my way around driving it out. After cleaning everything up, assembly was the reverse, carefully driving in the new bearings. The new lip seal was the most difficult getting started without going in crooked. Time spent was a good 8 hours (it would have been more if the outer drum was removed) and the cost of everything was $167.09. Thanks to Part Select, the spinner support assy came the very next day. The two bearings came from Bearing Supply & Depot Inc. The washer operates like new!! Very Quiet!!

I went on your site and found out the Bearings were not sold separately by Maytag and that they wanted $800.00 for the entire outer tub in which the bearings are pressed into. I read another post on your site where someone referenced some NSK bearing part numbers. I went to my local auto parts store that cross referenced the NSK number to Timken Bearings (a high quality automotive bearing). Following the instructions I hammered out what was left of the old bearings cleaned everything and pressed in the new bearings. When the Lip Seal kit arrived I pressed in the new seal following the instructions provided, reassembled the washer and it’s as good as new. Total cost just over $100 in parts and a few hours labor. Removal of the old bearings was a difficult task especially since mine were in such bad condition as water must have been slowly leaking into them for some time. If you have some basic automotive repair skills and or some knowledge of how to remove and replaced pressed in bearings I would recommend this repair. In my case money was the motivating factor with 2 kids in college and a wife who would have insisted on a new matching set of a washer and a dryer instead of just replacing the washer.

Using online disassembly instructions removed and replaced front and rear bearings. Then attempted to install the seal kit that was purchased online from partselect. Com. Was supposed to receive both seals plus lubricant so that no matter which seal I needed I would be covered. The kit I received had 2 seals that were identical. . . I needed, as it turned out the early seal kit, but unfortuneatly I had 2 revised kits. Of course I tried to assemble one but it just won't work. The seal kit must be the correct one. I didn't give up. I ordered another seal kit online from appliance partspros. Com and received both kits as advertized. . . One being the early version plus a small packet of grease along with all the other required loose parts and was able to complete the repair. The second time around proved much easier because of the experience factor.

Followed the instructions that were supplied with the Lip Seal Kit, for removal of the inner drum. As expected, once into the project, I found that the bearings that are part of the outer drum, were bad. Reading other installation blogs, prior to starting, I knew the bearing sizes, 6206-2RS & 6207-2RS, and I purchased the bearings, from Motion Industries, before starting the project. Taking a hammer and long 1/2" socket extension I was able to remove both the inner and outer bearings form the outer drum. (Bearings were all but seized up) Once I had cleaned up the aluminum hub which is part of the outer drum and where the bearings mount, I was able to start the process of installing the new bearings and completing the project. Timing could not have been any better to take on this repair project because the aluminum hub was showing major signs of corrosion on the inner side of the hub. I was concerned that the new lip seal would not seal off the inner drum from the bearings/outer durm. This project was competed on 8/21/12 and so far and 6 loads later I have not found any leaks.

I was sick when I heard the noise from our washer. I looked online at new ones and found out it was going to cost between $1000 to $1500 to replace it. While looking online I found the PartSelect site. Unbelievable! I put in the model #, read the posts, ordered the parts and within a few days they were in. Using the video and the posted instructions I took it apart and replaced the bearings and seals. The whole thing took about 3 hours and we were back to washing clothes. Total repair costs were about $160 to $180. Compared to the price of a new washer, you guys saved the day.

I referenced the enclosed instructions, and U tube videos, along with gasket I also changed the bearings for about $40. From local grainger, it seems to have solved problem, thanks for quick shipping,

Thanks to Partselect's accurate parts' lists, and installation video, along with others' posted installation trials, gained confidence to attack problem on my own (coupled with repair (or should I say, "replace")men's advise to trash machine). Bearings had basically disintegrated, causing inner tube to be out-of-alignment, and rub against outer tube. Would just like to add to what others' contributed, that I found Plumber's Tub Drain tool to work very well at knocking-out larger front bearing (was perfect fit to ID of bearing). Had to Dremel cut out rear bearing, but quite accessible from rear of machine. Otherwise, alot of cleaning from 13yrs. of useage. Thanks for everyone's assistance!