MAH21PDDXW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anna from Gibbstown, NJ
- Parts Used:
- WP22003275, WP22003075
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
An object had gotten wedged between the inner door and the spinning drum causing the grommet to wear down while spinning and the inner door to crack allowing water to trickle down the front of the washer. (word to the wise-never put a hard athletic support cup into a front loading washer)
I ordered the grommet and inner door on a Tuesday and had both parts at my door step the following day. Including shipping it was only $64.00. With only a screwdriver in hand and 45 minutes of time I removed four screws to take the entire door off. I then removed the inner door and vent tube and grommet (very easy). After placing the new grommet into the new inner door I inserted the vent tube and screwed everything back together.
The repair man would have charged $90 for the labor and the parts which he would have had to order would have been extra.
The repair man would have charged $90 for the labor and the parts which he would have had to order would have been extra.
Was this instruction helpful to you?
Thank you for voting!
One of the drum baffle's boke from it's mount
Removed old broken plastic grommet's and installed two new plastic grommet's. Attached new baffle using old screws. Used a short piece of picture frame wire to install the two new grommets by fishing them into place with out removing the washer drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Huntington Sta., NY
- Parts Used:
- 22003856
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Motor did not have the ability to rotate washing machine drum.
Removed old motor installed new motor.
Was this instruction helpful to you?
Thank you for voting!
Washer was so loud in the spinning cycle it sounded like a jet was taking off
We took the washer completely apart. Replaced the bearings, pulley and
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Louisville, KY
- Parts Used:
- 12002022
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
loud noise during spin cycle
got instructions off internet from others who did same repair; after taking inner basket out, used drift to remove outer bearing; seal was difficult to remove but used drift to force innner bearing into seal and seal popped out. had help reinstalling inner basket into outer basket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Wagoner, AL
- Parts Used:
- 12002022
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
seal went out bearings also had to be replaced
Had to remove the tub. Tha bearings had to be removed from the drum. After installing the new bearings(which are available @ O'rReilly's) the seal was't bad
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trang-Dai from Houston, TX
- Parts Used:
- WP22003275
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The inner door was dammage with a hole so we needed a new inner door.
Remove the ten screws to the inner door to remove it. There are components in the inner door that we didn't think would be there. Take out the components on the inside of the inner door. The areas where the ten screws go in have the small metal plates that we needed to be transferred to the new inner door. Otherwise the screws will not fit. It flips out. That's the part that took us a while to figure out but it came out easily. The other parts snaps on and off after the two screws are removed.
Just remember what you removed and where it should go. It takes two people to do the work.
Just remember what you removed and where it should go. It takes two people to do the work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Bethel, CT
- Parts Used:
- WP22002083
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water leaking around washer
First ya have to find the problem that takes time.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, found the crack ordered if from you guys.(very fast) slapped it in and put a load in.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, found the crack ordered if from you guys.(very fast) slapped it in and put a load in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Seminole, FL
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inner door skin worn from carpet backing rubbing in spin cycle.
Ordered part from PARTSELECT.COM, super fast shipping, next day actually, via fed ex. Part was exact replacement with no surprises. Swapped out internal parts snapped door lid cover in and was doing a wash in 15 minutes start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Allen, TX
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washing large object broke inner door
First I removed all the screws, which removed the door. Once the door was off, was able to de-install all the parts of the old door and install on the new door. The engineers that design this, made it to be able to replace easily. Inner door part was replaced in less than 30 mins. The most amazing part was I order the part on Monday and the door was fix on Tuesday before 2:00. I was amazed. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- max from antioch, IL
- Parts Used:
- WP22002077
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
leaking water at the seal between the drum and door assembly
I took the door off, front panel, soap dispenser(to lift the top out of the way)and took off the cross braces on the front of the machine. I pealed the door bellows off and took the drain hose apart; there was much gunk and debris to clean out...maybe something here was clogged? Removed all the snap clips and took the front of the tub off;the tub seal seemed good, but lots of grime/gunk build up.I cleaned all surfaces, put the new tub seal on,and put it all back togther. The hardest part was working the snap clips back on; I worked a few on both sides, top and bottom, and then filled in the rest. The machine has been working fine for a month now, no leaks:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Downers Grove, IL
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the inner door was leaking
First I remove the 2 screws that hold the door on then put it on the table on a towel not to scratch the door and unscrewed the inner door and changed it out easy stuff.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRIS from STERLING HEIGHTS, MI
- Parts Used:
- WP22003275
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Water leak on bottom outer door
Removed outer door and positioned it on counter next to new part.
Transitioned each part element from from one to the other.
Finally re-install door back in place..........
Transitioned each part element from from one to the other.
Finally re-install door back in place..........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FOLSOM, CA
- Parts Used:
- 12001788
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burn smell during spin cycle.
I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CHINA, ME
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
sharp metal edges
after cutting my hand I installed masking tape around the opening on the back of the washer. All went well after that
Was this instruction helpful to you?
Thank you for voting!