MAV6451AGW Maytag Washer - Instructions

Brought unit out to garage so I would have room to work on it. Popped the top off, removed two screws to remove the front panel, removed back panel also, since there was no way I was going to the trouble of dis-assembly to get to the snubber without changing those 6 springs also - and you HAVE to remove the back cover to access all 6 springs.Removed belt and level and drain hoses- tub came right out. Loosened those 6 screws without removing them and pulled old snubber out- very straight-forward. Spent 10 minutes just comparing the old and new snubbers- I saw that there's a "ridge" around the inside of the new part that is gone on the old snubber. Sprinkled some corn starch at base of unit where the new snubber will fit (Great Idea someone had!) After everything was re-assmbled, I noticed the tub was now nice and tight when I grabbed it to move it. Before, it took no effort AT ALL to move it all around. Did a test load with some laundry the wife had stacked on the drier. Imagine my disappointment when I heard loud knocking inside when it started to agitate, but not while it spun!
Got all my tools back out and took the wet laundry out to take it all apart again- found the wife's heavy glass vase had been hidden in one of the towels. Re-tested- everything works GREAT!So far I've changed the drum seal (hardest) and the waterpump (easiest)- thi springs and snubber was alsmost as easy as the pump.
Above average shipping from Parts Select also- very helpful and efficient people on the phones.

Pop the cap off the agitator/auger no tools needed. Once removed select a socket and a socket exstension. remove the screw amd pull off the part. Make sure to save the washer that may be still attached to the inside of the agitator. install the new agitator using the existing screw and washer. Takes about 15 minutes.

First I raised the top and took out the two screws that held the front on. Then I removed the back panel which were held by 4 screws. Then I turned the machine on it side and removed the belt. I then pulled the hose off from the tub to the water pump and the small hose on the back of the tub. I then removed the 6 springs that held the tube to the base and then I picked the tub up and turned it over on the floor. Then I backed off on the screws that held the snubber in place. I pulled the old snubber out, retighten the screws that held the snubber tight. Then I reversed my steps.

As described in video; however, the video does not match the model I repaired. Most stuff is the same. Hardest thing to do was installing the new springs on the back of the tub (2 of them).

Removing and installing the pump is theoretically easy, as everyone on this site has said so far. Just remove three hex-shaped screws, loosen drive belt and remove pump, then install new one using the same steps in reverse order. The trick is getting the screws off and on--they do not have slots for a screwdriver and there is not room around them for a socket wrench or pliers. I probable spent over an hour just on removing/replacing these screws and have many bruises to show for it. I ended up attaching a vice grips on the tips of the screws underneath the washing machine and screwing them out that way. And replacing the drive belt was horrifically difficult--that's where the other hour went. The devil was definitely in the details! If anyone had told me what I would have to go through to make this repair, I would have called a repairman. And I am an extremely handy person--I do stuff like repairs all the time, so it is unusual for me to say this. The good news is that the new pump works and the washer is back in commission.

After taking the motor off (it looked loose to me!) and stripping out the bolts on it, then finding that the bolts holding the motor were permanently affixed to the motor (and they were an odd size not available at the hardware store), I drilled the bolts out and put in new ones (on the motor) and re-affixed the same. I still had a problem. I then went online and found that most people had problems with the water pump. I looked at the pulley on the water pump and found that the inner shims had slipped out on a permanent part (and could not be put back in with the basic tools I had on hand). I ordered the pump online, and replaced the same. Took about 30 minutes after I found the real problem and got the parts in. My pump had a permanent metal disc on the bottom which did not come with the new pump, but the new pump fit without it. Machine works fine now.

I removed the old pump put the new one in its place. In twenty minutes i was ready to was clothes. It was so quite i thought something was wrong. I received the part in three days the timing was great.

Removed front panel from washer,removed belt, used 1/2 inch socket setand channel locks to remove hose and pump. Installed new pump, reinstalled hoses and belt, and placed front panel on machine.

Removed old belt and pump,installed new one.

tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.

simply replaced the timer.thank you for perfect service

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

i removed 3 screws from back of washer , took off 2 hose clamps , then i took 4 screws out of waterpump, removed belt . put new pump on very easy. thanks part was perfect, fixed problem

I watched video, couldn’t believe how easy to replace

Tilted machine back, put a paint can under it and did R & R with belts.